Search results

  1. PaulyV

    control cables (2) for 1988 Johnson 48 spl.

    I'd like to purchase control cables from Iboats for this motor 20' length. Do I need to select 2 in quantity? or are they sold as a set?
  2. PaulyV

    why is this a GOOD idea to paint the hull where the flotation is

    saw this in a thread a few minutes ok. Im curious to know why this was a GOOD idea.
  3. PaulyV

    1977 Evinrude 55hp Power Pilot Substitute?

    Looking to change my center console to this. It’s a Better size suited to my boat Can I use that OMC control (in pic) on my 77 55hp? Or is the power pilot specific to this engine due to warm up lever.
  4. PaulyV

    77 evinrude 55 hp oil leak

    Oil/ Gear Lube supposed to be leaking out of this hole? Its making a mess of my water barrel...and other things.
  5. PaulyV

    1977 Evinrude 55hp. Whats this tag signify?

    Was power head changed at some point.
  6. PaulyV

    Proper Starter Pinion 77 Evinrude 55 HP

    Evinrude 55773d. It shows 2 starters Prestolite or American Bosch. My gear pinion is 10 teeth not 9. Stop nut backed out while on water..I think the pinion separated. I used nylon nut from steering wheel to put back together or I'd be somewhere adrift in Long Island Sound. Got back to dock and...
  7. PaulyV

    1977 55 hp Evinrude choke spring?

    I was making an adjustment on my throttle (start) tab that contacts the plastic roller and this spring came loose, then off. From reading this holds the choke open on WOT. Does anyone have a diagram of how this goes back on and where. Motor still runs fine but I imagine once on water with a load...
  8. PaulyV

    "77 55hp Erude prop

    need a new prop, found a few rocks hiding. i have a 1972 Starccraft 16" SS Center console 2 batteries in front of console, leaning post. Gas tank ( 12 gallon) rear. Prop size is 11 3/4 x17. I've read that props for a 13'-15 boat, light weight. (whaler?) I notice there are 12x 17 . should I...
  9. PaulyV

    1960 Merc 700

    I am going to look at this tonight. used 1 season. Been in storage in gentleman's garage for 60 years. pristine. Gas lines brittle and cracked. Motors free turning. Wants 900.00. Any comments.
  10. PaulyV

    1965 Big Twin 40 hp short shaft

    My 1972 16' StarCraft Super Sport has a 20-21 inch transom . I want to mount my 65 Big Twin short shaft . Anyone know of a reverse Jack Plate that will lower me 4 inches? I've looked and looked and have quite a headache. Even a jack Plate that will lower instead of raise 5" would be helpful...
  11. PaulyV

    Not permitted

    Not permitted Closed
  12. PaulyV

    I need THIS manual trim tilt relief valve. 1987 Merc 70hp.

    Installed new t and t pump. neighbor CUT this he said it was too long..LOL..now pump wont cycle due to missing gaskets. The ones I am seeing are not recessed (threads) like this..to allow passage through transom arm. Any ideas where I can purchase this ? Thank You!
  13. PaulyV

    how to disable oil injected on 1987 70hp mercury.

    looking to disable oil injection and pre mix 50:1. Anyone have steps to do such a thing. Thank You
  14. PaulyV

    Binnacle Control.Support Blocks?

    I am looking at purchasing this control for my 1987 70hp Merc. In speaking with the gentlemen selling the unit, he states the support blocks are not with the unit. he also mentions that they are purchased seperately depending on type of cables used. Is this true? I cannot find a supplier of...
  15. PaulyV

    washdown kit question

    deleted post
  16. PaulyV

    Primer NOT adhering to gluvit after sanding/wire wheel

    OK..I resanded AND wire wheeled the areas that spidercracked. I wire wheeled almost down to the bare aluminum, pretty much removing most of the Gluvit I applied....and still after 30-40 mins..it seperated. The aluminum primer is Latex based. is this the issue? Will oil based paint adhere better?
  17. PaulyV

    primer spiderwebbing on Gluvit

    deleted post
  18. PaulyV

    1987 Merc 70HP..Top Mount Controls ??

    Hey guys..here are a few pics of my control cables/ harness. is there a universal Top mount Control TNT that i can use for this motor. Or if you can recommend a Brand top mount control. Thanks in advance! By paulyv, shot with KODAK Z650 ZOOM DIGITAL CAMERA at 2009-12-29 By paulyv, shot...
  19. PaulyV

    How about SeaCraft?? anyone have info on them?

    I jus picked up a SeaCraft 16' CC. 1981 Hull..This boat is one solid piece of glass. Anyone have information on them..I did go to the website and found that this is one of the most desirable hulls out there. Any help is appreciated.
  20. PaulyV

    1987?? 70hp

    Serial # ob196255 from what I can make out from the charts is this a 1987? Any help appreciated.
Top