Search results

  1. Woodstock60

    1995 force 70 hp ignition help

    I know their is a section on this in here, but my head is spinning with numbers and I'm not very good with electric testing, and I have a 5 day fishing trip coming up in 2 weeks and I'm panicked. My problem is on this motor, suddenly no spark at all on all 3 cyl. , thought it was the stator...
  2. Woodstock60

    Saltwater eating my trailers...

    Need some ideas of something to coat my trailer with, im going on my third one in 5 years. I do fish a lot and launch my boat in the brine about 40 times a year. I was thinking maybe an under coater . anyone have any ideas\ suggestions?
  3. Woodstock60

    1987 fisher sv-16 dlx partial restoration

    I know that these boats aren't exactly the top of the line, but I picked it up fairly cheap ( boat and trailer) $ 700. And 16' are hard to come by. First pic is the condition i started with. 10,000 rusty self tapping screws held the one piece all aluminum floor down. And the floor felt solid...
  4. Woodstock60

    Aluminum hill repair : need fastener ideas

    I am repairing broken ribs on 16 ft. Sylvan aluminum boat. I am using stainless steel screws and am looking for ideas on how to keep the screws from touching the aluminum and causing huge corrosion holes. Thanks in advance
  5. Woodstock60

    1964 40 hp steering tension broke

    I have a dozen of these older 40s, all different years but they all have one thing in common. The steering in them are all loose. Does anyone have a fix for this. I'm not sure how to get in there without tearing the whole thing apart. Any advice would be appreciated. Thanks
  6. Woodstock60

    early 1960's 40 hp spark plug issue

    The lower cylinder started cutting out on this motor, so the first thing I checked was the plugs and the lower was loaded with wet gooey carbon. I cleaned both plugs and reinstalled and ran for a few hours, she started to run rough again so I pulled the plugs and the lower was starting to load...
  7. Woodstock60

    Tiller arm on 1962 40 hp lark

    I installed a tiller arm on this motor and for some reason the throttle has a lot of pull back on it. It has the feeling of being spring loaded and as soon as I take pressure off of throttle it snaps back and I loose power. Its just a chore. Ive lubed all the correct areas. Anyone have advice...
  8. Woodstock60

    Timing procedure on 40 hp

    on my 1962 40 hp I believe the timing is off. I read the top secret files on this and just don't understand. I need it dumbed down. I don't know where the timing marks are, or how to advance it. I don't know what the full spark timer advance stop screw is . Ihave timed vehicles before, I just...
  9. Woodstock60

    62 40 hp adjustment

    Well, I finally have this motor running fairly smooth, Idle's nicely, runs good at med and WOT. The only problem is when I ease of the throttle to move slower she wants to die out momentarily. almost like its flooded, she comes to right away if I give a little gas, but its not right, Just...
  10. Woodstock60

    1962 40 hp no spark top cyl.

    Motor 35531 M 1962 40 hp. Running fine the other day and started to loose power, but would still run, I could hear one cyl. cutting out, so I limped in on one. First popped off fly wheel and checked points, not that, put on plug tester lights and saw top cyl cutting out intermittingly, so I...
  11. Woodstock60

    1962 40 hp evinrude choke dilemma

    Ive begun to restore this motor model # 35531M. It has a choke system I have not seen before on these motors. coming off the side of the carb is a housing that is controlled by a vaccume switch, the choke when cold is closed, upon starting the vaccume ****ch pulls it open and Im guessing remains...
  12. Woodstock60

    40 hp generator wiring

    I found a 40 hp electramatic ( RKL- 30 C ) with a generator. Looks like I can rig it up to my 33 evinrude ( 33653 D ) How do I wire it up to charge my starting battery. Everything on the 40 is electric and wired into a general connector which I dont use on the 33 , I just have the two leads...
  13. Woodstock60

    1959 Super Seahorse 35 hp remote cable assy.

    I have the above mentioned motor I want to restore. This model has a cable mount opening in the pan for what appears to be remote start, choke, kill switch and maybe more, it has 5 or 6 pins sticking out. I looked the part up and its 377278 cable assembly. I tried looking around at my usual...
  14. Woodstock60

    1962 28 hp spark issue

    This one has me baffled. followed procedure to wake a sleeper, as I have many times before. rebuilt carb, new coils, regapped points, sprayed in double oil mixture into carb intake while carb was off and cylinders. put in new plugs and added electric starter, Changed all gas lines to new rubber...
  15. Woodstock60

    9.5 carb

    I use this as an emergency motor so it rarely gets used and of coarse when I need it she wont start. Im constantly working on the carb, I have at least 4 of them and I just cant get it right. It seems that there are a few plugs on this carb that are always leaking air, What do you guys use to...
  16. Woodstock60

    1960 3 hp evinrude

    Does anyone have a manual and breakdown of this little guy? Thanks Quag
  17. Woodstock60

    33 hp lower unit seals

    Im resealing my lower unit and am having a bear of a time getting the old driveshaft and propshaft seals out. I dont have any seal pulling tools, does anyone have any suggestions on a home made tool or an alternate tool besides a hammer and chisle. Thanks... Quag
  18. Woodstock60

    1968 9.5 recoil repair

    Does anyone have any tips or tricks for fixing the recoil on this engine? Thanks Ronnie
  19. Woodstock60

    1958 super sea horse 35 hp broken piston

    Thats what I have. I want to replace it with one from a 68 evinrude 33 hp powerhead- looks the same but I can't find any info to confirm.... any takers?
  20. Woodstock60

    35 hp Super sea horse compression release

    I just picked up a 1958 35 Super sea horse, and allready had a 59. One of these motors I plan to restore and the other I plan to beat the crap out of on the bay. My question is can I remove the compression release mechanism on my bay motor without affecting the motor operation (beside the...
Top