Search results

  1. berry79

    1808 Biax Conformabilty

    I was just curious to how 1808 biax conforms to corners and angles. here is were I am at now. It consist of a layer of 1 1/2oz csm and a layer of 24oz woven roven. I would like to put a layer of 1808 on top of this up to were I outline with the red line. Do you think there will be any problem...
  2. berry79

    Resin Application Rollers

    What does everyone use for rollers when rolling out poly resin? I just bought some, I believe they are glassright brand, $7 and change a piece. I will be using them to role out 1 1/2oz mat and 1808 biax. Is there something they sell at HD or lowes that will work just as good? Also one other...
  3. berry79

    Some more poly resin questions

    I tried searching again before this post, but almost every post shows up when you search for polyester resin. I have few questions on some things I confused about. 1. I read somewere that you only need to add wax to the resin for the last layer so it cures with out being tacky, this way it can...
  4. berry79

    Stringer Construction

    I tried searching before I created this post, but you type stringer in the search box and it pulls almost every post in the restore forum. So this is my questions. I'm going to be building my stringers shortly and need them to be about 17' long. I have read everywere about a scarf joint being...
  5. berry79

    Aluminum or Plastic Fuel Tank?

    Just currious to which tank everyone prefers. I'm getting ready to lay down a new floor in my center console and want to replace the tank before hand. I have a Moeller plastic tank 45gal in there, new from 1993, and it just seems to be very britle. Though the reviews I have been reading all lean...
  6. berry79

    Cap Glued To Hull What To Do?

    I'm getting ready to pull the cap on my 19' CC. Everything is loose except for this type of resin that sits between the stringers and the floor. The stringers are foam core, and are about 10" wide. What is the easiest way to get this bond freed up? I really can't get anything in there to cut it...
  7. berry79

    ? Cutting Cap At Transom

    I'm preparing to remove the cap to repair floor and transom. While cutting the lower section of the transom cut out I noticed about a 1" layer of filler. This was not present while cutting the side. My question is should I be cutting below this fill at the wood and not the lamination line? Also...
  8. berry79

    Filling Big Holes In Transom

    Hello everyone. I'm in the process of redoing a floor and transom in my boat. I will be using the nida-bond pourable transom and have some big holes in the transom that I will not be using anymore. Just was in need of some input of how to block or cover these holes before I do the poor. On the...
  9. berry79

    What Brand Epoxy Resin?

    Just wondering which brand of epoxy resins does everybody use? Is it worth the extra money for the west system? Has anybody tried this system? http://www.fiberglasssite.com/servlet/the-Resins-cln-Epoxy-resin/Categories If so how did it work? Or is there other brands you guys could...
  10. berry79

    1994 Evinrude 115 Removal

    I will be removing a 94 rude 115 with the cherry picker. Wondering were you are suppost to hook the chain. Do you make a lifting rig to screw into the three threaded holes in the fly? Or is there some way I'm just not seeing?:confused: Thanks for any replies.
  11. berry79

    Anyone used one of these?

    First, I would like to thank everyone on this forum. Because of this, I now have the courage to tackcle my transom and floor replacement myself. I was just curious if anyone has used this or something like it to remove things like the inner fiberglass skin, sections of stringers, etc. Thanks...
Top