Search results

  1. V

    sierra 7350 pump vs. sierra 7352 pump

    the 7350 is for the 9.9-15 hp, the 7352 is for 20-25 hp, so I'm assuming the 7352 pumps more volume. What I'm wondering is if the mounting gaskets are the same. Thanks in advance. Chris
  2. V

    gear selector handle '57 18 hp 'rude

    my handle is turned upside down, how do I turn it right side up? Chris
  3. V

    57 18 hp kill switch conformation

    If I studied right in the old threads all I have to do to wire in a kill switch is to ground out the hot wires on the points? And the switch is a closed circuit? Chris
  4. V

    from tiller to remote steering '57 evinrude 18hp

    I know nothing about what I need or how to do this. Could anyone give me guidance? I need a list of parts. I have a simplex box, but the rest I dont know what I need. I know that I need pre 79 cables, but the problem is the fitting and such that connect the cables to the motor. I also need some...
  5. V

    fuel pump differences

    I've heard the 7351 pump is better than the 7350, but haven't been able to find out what the difference is. I had the fuel pump conversion done on my '57 18hp and it still wont suck fuel. Im wondering if the pump might make the difference. Chris
  6. V

    still same old prob fump conversion

    Im working on a '57 18hp rude. I finally got the thing to pump, but it will not keep up with demand of the motor. I have to pump the primer to keep it running, but it will run aprrox. 45s before having to pump it again. This varies a little with the motor speed. The things that have been done...
  7. V

    bionic fish finder

    Has anyone ever heard of these? What do you know about them? Chris
  8. V

    will this be enough?

    I have a 1546 jon boat and I went with a 50lb. minn kota. Will this be enough trolling motor? Chris
  9. V

    what size trolling motor?

    I have a 1542 jon boat and am going to buy a trolling motor, I was wondering what would be a good size for it. All info is appreciated. Chris
  10. V

    solenoid

    Im working on a '57 9hp rude and was wondering if it would be ok to mount the solenoid beneath the top or do I need to mount it on the boat. The boat is a 15' aluminum jon. Chris
  11. V

    starter schematic

    Can anyone direct me where to a wiring schematic for the electric starter, solenoid, and key switch? I'm working on a 57 18hp evinrude with only the electric choke and starter wired to the switches. Chris
  12. V

    up, up and away

    How far up does my motor need to be in relation to the bottom of the boat? Im running a 57' evin 18hp on a 1542 jon boat with a 16" transom.
  13. V

    18hp evin throttle question

    1957 18hp when I turn the handle to WOT the back butterfly in the carb is not all the way open. I adjusted the plate that the roller follows to open the throttle and it didn't seem to help any. Is this plate supposed to be flat at WOT or is it closed a little bit. The reason I'm asking is that...
  14. V

    what do you think of this

    What do you think of the new 15ft tracker topper? I'm thinking of getting this. It has a live well, and the skin is .063 versus .043 thick for the 14ft. boat. Is it worth the $370 price difference? Chris
  15. V

    57 evinrude question

    18hp, does it have a throttle adjustment on it? Chris
  16. V

    help please!!

    Is there a timing adjustment and is there a way that my throttle linkage could be out of adjustment on my 57 18hp evinrude? It was very smooth when I ran it on the water but just felt underpowered for an 18 hp. Ive had theignition plate off, not sure if I knocked it out of timing or adjustment...
  17. V

    runs good, but want to check some things

    Ran my 57 18 hp on the water for the first time today and it ran good, but felt weak. I'm know that the high rpm is 4800-5200 and it ran very smooth up to full throttle, I need to know how to check and make sure that I'm getting all the throttle out of it. I also need to know if there is a way...
  18. V

    sunday is the day

    Well after much problems with this motor(57 18hp), I finally got it running good. Sunday it hopefully will do time on the lake. It has been a trial to get this thing running and I need to thank everyone who helped me by giving advice and suggestions.You have been wonderful and this site is a...
  19. V

    please help Im getting close

    Im working on a 57 18hp evinrude. Popped the flywheel off and the grounding wires have been eaten through. Coils are off, but I need to know how to get the whole ignition plate off so I can change wires. How do I do it? Chris
  20. V

    what to do?

    I need new ignition coils for my 57 18hp, what should I use? Mallory, sierra or CDI?
Top