Search results

  1. 1

    stator testing question.

    hello to all. I have a 1977 70hp evinrude. I just got my DVA adapter for my multi meter so I can test the stator,etc. can someone tell me what the multi meter is to be set at for testing and procedures for this
  2. 1

    1977 evinrude 70hp(70773) timer base question

    I was on the CDI troubleshoot website and the OHMS resistance for the timer base was between 10-20. I used my multi meter with timer base wires disconnected and got 7. Im still waiting on my dva adapter but if the reading is that low can I automatically say that the timer base is bad without...
  3. 1

    1977 70 hp evinrude (70773)

    hello to all.... can someone please send me the wiring diagram for my outboard motor particularly near the power pack and terminal block. I disconnected wires and need to reattach. the display on cover is faded. thanks
  4. 1

    1977 70 hp evinrude electrical issue

    hello everyone.... I have been troubleshooting a no spark issue and here is my question. I disconnected the wire for each coil from the power pack. I then connected my light tester clip on the screw for the #1 coil and then grounded the test probe and cranked the engine and the light came on...
  5. 1

    evinrude shift control box issue

    first of all thank you to all the iboat community for assisting me with my other problems. one last problem or issue though. i have a 1977 70hp evinrude (70773) with a power pilot control box. without the cables attached to the motor i can shift the motor by hand to forward,reverse neutral. but...
  6. 1

    waterpump installation

    heres a quick question....when installing the waterpump do you use sealant anywhere on the waterpump. also when reinstalling the lower unit to the housing...no gasket????sealant????:confused:
  7. 1

    waterpump installation

    heres a quick question....when installing the waterpump do you use sealant anywhere on the waterpump. also when reinstalling the lower unit to the housing...no gasket????sealant????
  8. 1

    carburetor float hinge pin question

    I know that this is kinda stupid question but can you not get a metal hinge pin instead of that crappy teflon(or whatever its made of)pin. if so where or can I use something else.thank you
  9. 1

    1977 70hp evinrude starting issue

    hello to all. Okay here is my problem. i aquired a control box and cables for my 77 70hp evinrude. I disconnected the old cables from the engine and proceeded to run the other cables when i noticed they were rather longer than the old cables. didnt think it would matter so i stuffed everything...
  10. 1

    1977 70hp evinrude lower unit removal

    Hello one and all. I am needing some help with my 1977 70hp evinrude. I am planning on replacing the water pump due to overheating. can anyone tell me how to remove the lower unit to gain access to the water pump. any info sent my way would be appreciated. illustrations or instructions would be...
  11. 1

    1984 yamaha outboard carb parts

    do anyone know if there is a website or place i can find a main nozzle for the carburator. motor model is 115etln. all the yammy sites is saying it is discontinued so i guess i need a used main nozzle. thanks for your help
  12. 1

    1975 grady white with a omc 165hp gm

    hello looking at a project boat but the engine block has a rust hole in it. can i put a different motor in this or do i have to put the same model in. any help would be appreciated. it has a omc 165hp 250cu/in 6 cylinder gm motor
  13. 1

    1985 yamaha 115 outboard wierd problem

    hello I just bought a 1985 boat and motor. I replaced the four plugs, fuel pump and primer bulb just as a precaution. unloaded her and and started the motor. immediately the motor started running rough. it sounded like the thing was sneezing. it would run and then sneeze. i noticed it even blew...
Top