Search results

  1. O

    Yamaha 8 HP Help!

    Hello. I pulled off the lower unit and the screw that needed to be loosened for the shift rod broke and when i pulled the shift rod came off from the lower unit instead. so now i pushed the rod back in the lower unit and it when in twice but not the third time. do i need to pull apart the...
  2. O

    Johnson 4 HP - How to tell if cylinder toast?

    helllo. i was using my 4 hp the other day and it died and then i started it again and then it died for good. i couldn't even pull the cord. it doesn't move. there is a piece of metal and a metal attachment piece that was floating around under the cowl but i don't know if it is related. i pulled...
  3. O

    Honda 2HP 4 Stroke BAES-1201877 year?

    please tell me the year? thanks!
  4. O

    Johnson 9.9 runs rough and won't idle

    Hello! please help. i have a 70's johnson 9.9 and i finally got it to start but only when the throttle is full. it won't idle and runs likes it is missing. i checked the compression and it is fine. i changed the plugs to new and that did nothing. i am thinking it is the points under the flywheel...
  5. O

    Outboard trouble ?

    Hello. I have an 18 HP Evinrude Fastwin 1968. I just bought it and when I rev it high in gear it stops going. it keeps reving higher but no speed. Could this be the gear slipping out? the propeller? the gears/clutch dog? or movement of the trim/tilt? I first thought it was the gear handle...
  6. O

    Bayliner Capri 1850 5.0 Liter

    I have what I think to be a Bayline Capri 1850 5 Liter. The engine is rusted. The prop has a chip in it. The hull seems good. The trailer is rusted but maybe serviceable. The wood floor has a hole in it, needs to be replaced. The interior seats all must be thrown out. So, what should I do with...
  7. O

    1968 Evindrude 18 Fastwin Shift Handle

    Hello. The shifting rod on the motor is sheared off right at the power head. It currently is tapped so a screw can be used to shift gears. So, how hard and what do I need to do to replace the rod that comes out and connects to a gear shift handle? Is there anything I can do to make shifting...
  8. O

    1975 Evinrude 85,115, or 135 HP?

    Hello! How can I tell if my outboard is a 85, 115, or 135 1975 evinrude? There are no identifying plates or stickers. Thanks!
  9. O

    1968 Evinrude 18 HP Fastwin Choke

    Hello! The choke connector slips off the lever frequently. Is it not hooked up right? See pictures. The rod arm slips off the little metal stub piece it connects to to move the fuel control. Any ideas? I checked the parts diagram and it seems like all the parts are there. Maybe the rod needs to...
  10. O

    1968 Evinrude 18 HP Fastwin fuel line

    Hello! The fuel line from the connector outside of the cover and into the power head is kinked. Does anyone know if I am missing a part? The kink would impeded gas flow I am pretty sure. I might have it connected to the wrong hole and the wrong connector? Maybe the hose needs to be stiffer...
  11. O

    Please Help me identify my outboard?

    Hello! Please help me identify this outboard. I was told it is a 120 or 130 HP. It looks to me like a Johnson or Evinrude 1970s. There is no identification. Can you please help me by looking at the pictures? Thanks so much!
  12. O

    Mercury 850 control box handles?

    Hello, I just bought an old boat and don't know what the controls are for. I haven't driven a power boat with controls for awhile. I figure the large handle is for the gears and throttle. It has a neutral marked on the box when upright. But there is another handle that is against the starboard...
  13. O

    Mercury 850 What to do? Help!

    Hello, I just was given a Wellcraft 165 Airslot which has a Mercury 850 on it. The lower unit is off and taken apart. Some of the parts are rusted. The powerhead looks clean. I tried to compression test it by hooking up a battery and turinging it over. It tested at 95-100 for all four cylinders...
Top