Search results

  1. M

    How to replace belt

    The engine is an '82 OMC 2.5 liter 4 cyl. How do I change the belt? The steel brace for the trim is in the way. I do realize I may have to take it off, but what is the right way to do this and what is the torque of the bolts supposed to be?<br /><br />Anyone have a part number or should I...
  2. M

    firing order

    After putting in a set of points just before winter, we (a friend and I) jumped into setting the timing today. The marina said it ran, but not well when they winterized it. Of course there was problems. For some reason the condensor went bad during the winter (I had replaced it along with...
  3. M

    wont start!

    Getting ready to take it to the service dept to have it winterized, but can't get it to start. Been like this for about a month or two. Was given some suggestions at work.<br /><br />This evening...I unplugged the coil wire from the center of the rotor cap and attempted to hold the end of the...
  4. M

    what kind?

    What kind of spark plugs do I need. Engine is 2.5L GM. OMC I/O. 1982 model.<br /><br />Thanks.....Bill
  5. M

    emergency cut off switch

    I have an older boat. A 1982 MHP 16ft tri-hull with a 4cyc GM engine (inboard)with OMC sterndrive. It does not have an emergency cut off switch and I am wanting to put one on it. I got a new one off of ebay, but now I am concerned. Here is the name of the switch...T-H Marine KS-1 Saf-T-Stop...
  6. M

    fuel filter

    Does anyone have the part number for a fuel filter for this setup? 82 omc sterndrive 2.5L. Is this also a fuel/water seperator?<br /><br /> omc fuel pump
  7. M

    Gear Lube level

    After reading a previous posting I think I know why lube is put in from the bottom with the top plug out...to release air bubbles? But can I simply take out the top plug to check lube level?<br /><br />Thanks.
  8. M

    steering wheels

    I just finished recovering the inside of my boat and now want to change the steering wheel from brown to black. My concern is the space between the dash and the back of the wheel, I guess you would call it the steering column. As of now there is a plastic brown piece that covers the steering...
  9. M

    Part number needed.

    I was able to do some searching on the internet and cross referenced an OEM part number (383444) with a "NAPA Echlin" igniton coil (IC10) that is on my 1982 OMC 2.5 liter. Done some searching with both number and found a matching coil at Autozone. Now I need an OEM part number for plug wires...
  10. M

    how do i know?

    I am needing to replace ignition coil and while I am at it replace points, condensor, rotor and cap. I have seen several descriptions of parts on web sites. How do I know what to order? Are there numbers on my existing components?<br /><br />1982 OMC 2.5 liter in-line 4 cyl.
  11. M

    test run...failed

    Thought I was doing good. Now I am back where we started. This is how it went today, after a carb rebuild and testing it under load at a local marina. 1982 OMC 2.5 liter (4cyl) OMC sterndrive.<br /><br />On the way to the lake, stopped by Wal-Mart and picked up some gas treatment. Then...
  12. M

    Which manual?

    Me again. 1982 OMC 2.5 liter(4cyl), OMC Sterndrive. <br /><br />Looking at manuals. Which is best or recommended? Clymer, Seloc, any others?
  13. M

    Impellar Check

    I have a 1982 OMC 2.5 liter (4 cyl) with OMC Stearndrive. How do I go about checking my impellar? It has not overheated but since I rebuilt my carb I am wanting to go ahead and check things for preventive maintanence. Also, what should I expect normal operating temp to be?<br /><br />I don't...
  14. M

    carb rebuild...stumped...problem solved????

    I am in the process of rebuilding a rochester 2 bbl carburetor. (talked about in another post)<br /><br />Everything has gone well up until this point. Now I have a question. It has to do with the location of the fuel needle and seat above the float. I have put in the fuel needle seat and...
  15. M

    Trim works...sometimes.

    Almost have the carb situation taken care of, but I have another problem at the same time...my trim.<br /><br />1982 OMC 2.5 liter. The trim is a screw type jack that is mounted in front of the engine.<br /><br />The previous owner said he had a problem before with the trim not working. It...
  16. M

    trim switch...which is correct....

    Did a search on this but could not find the answer. I am having trouble with my trim. 1982 OMC 2.5L It has been working fine, now it is hit and miss. After cranking it back down with a wrench and socket I was able to get it working. Again, hit and miss. Thinking it may be the selenoids as...
  17. M

    Trouble when giving it the gas!

    Ok...here goes...sorry in advance for the long post. <br /><br />Bought this boat from my brother-in-law. It has an inboard OMC 2.5 liter. 1982 Model MHP Advantage. Took it out on the water today. Pushed away from the dock. Fired it up and went about my business. Everything working ok at...
  18. M

    about my boat

    Where can I find some info on a boat made by a company named "Melhart Products"? Never heard of them before but the boat is in pretty nice shape. It has a 2.5L OMC inboard/outboard.<br /><br />Thansk
  19. M

    omc ignition

    About the post on the iginition labeled for "battery". I have, I believe, 2 wires going to this post. Actually, it is two large wires, not sure of color right now, that go into one smaller wire with an inline fuse. Can anyone help me with what these are. I would imagine that one is battery...
Top