Search results

  1. C

    mercrusier 5.7 vs 7.4

    I have a 1990 larson 25 ft 5.7 alpha set up ,i was looking at a 7.4,1993 brov. would this work wt.difference/hooking up what will have to change if anything.mercrusier
  2. C

    mercrusier 5.7

    i need a new engine my boat a 25 larson san marino has a 5.7 big block can i down size on engine to save fuel if so what engine would still move the boat well.
  3. C

    70 hp Evinrude trim question

    I just bought this 17 ft with a 70 hp ,the motor does not have trim,can i use any trim or does it have to be for johnson/evinrude ,it looks like a basic 2 bolt ,2 wire.
  4. C

    carburetor electric choke wireing

    i am switching back to electric choke ,there was a newer set up ,turn key start that is not working ,what 2 wires go to my older carb.that works good, i started the engine and ran it 15 min. to warm up ,runs great, no stalling idle is ok, do i need to hook up wires to the choke,if so which 2...
  5. C

    pre alpha shaft size,1980s,what size prop nut.

    what size prop nut is used on a 1980s pre alpha lower,i went from a 1990 lower drive to a older pre alpha drive the prop nut is to small i think im looking for a 7/8 i can not locate one.
  6. C

    1990 alpha lower/swap for 1983 lower

    i have a 1990 alpha ,my lower is junk,i went to look at a 1983 that is in good cond,will this match up with my upper,i was looking for sn.numbers on the 1983 we could not locate any,also mine is a 4.3,i belive the 1983 is from a v8 i know my ratio is 1.81.
  7. C

    fuel gauge issue

    i have 1990 maxum,ok the gauge works i had it tested,i am getting power from the sending unit,where do i look from here,i looked under the dash where all the wires are ,not sure what to check from here,there are a few blue wires that are taped up.thanks
  8. C

    1990 maxum soft spots on floor

    i have a 21 maxum i have done a lot of work on this boat i have a few soft spots on my floor i just want to get the rest of the summer in i plan to replace the floor during the fall months how can i make the few spots on floor stronger i was thinking of useing fiberglass tape w/a fiberglass...
  9. C

    4.3 closed water cooled to fresh water cooled

    i am doing a repower 1990 4.3 v6,i bough a long block from rapido,what is involved in going to fresh water cooled,i run mostly in salt water,it rots everything,i am useing many new parts to build this engine,is it poss.to go to fresh water cooled,dollar wise......
  10. C

    4.3 therm.houseing old style

    i am doing a repower chevy 4.3 v6 1990 -merc does not make an old style therm. houseing for these yrs,i found one it comes in 2 parts,the problem is it sits up to high so the fuel line hits the houseing,are there any other houseings i can use that sit flush to the intake.
  11. C

    4.3 belts,double to serpentine

    i am in the process of doing a reman job,4.3 chevy v6, i would like to convert ,to serpentine,belt,instead of haveing the 2 belts,what do i need to change,pullys ect,what parts will i need,other than just the belt.
  12. C

    edelbroock 2111 intake manifold

    i purchaced a new edelbroock,2111 in take that im going to match up with a withanew 4 barrel carb,what therm.houseing can i use,4.3 v6 chevy,the houseing is a 45 dergee angle i seen one from mich.motors for omc will this work.
  13. C

    4.3 chevy valve covers

    is there any difference in marine valve covers vs reg. v6 4,3 covers for a truck or suv blazer,they look the same,4.3L chevy 262,i am doing a reman job on my 21 ft cuddy,i need new valve covers,to many rusted parts off my old engine to metion, i was checking out these chrome type covers thought...
  14. C

    in take manifold 4.3

    can i use a chevy 4.3 ,intake manifold from a chevy blazer on a reman 4.3.1990 v6,they no longer make 12 bolt intakes,for these remans in these yrs,thats the problem that people will have when they buy a reman in earley yrs,its all vortec now,i can find plenty of gm intakes for chevy trucks-suvs...
  15. C

    alpha one gear ratio

    i have a 1990 4.3 mercrusier alpha one i was checking out sei i see they have different gear ratios which one will match i see on sei chart it has 184/181 i think its 181 whats the difference.
  16. C

    Vertglas gel coat system

    i have a 21 cuddy the jel coat needs att, vertglas system check it out does this stuff work ,has anyone tryed this out,i started compound and buffing im already tired of doing little sections at a time,the shine is comeing back but i have a long way to go,are there any short cuts, they claim...
  17. C

    bottom prep what grit paper to use

    i powerwashed bottom i do not get a lot of buildup any since i trailer,the hull was painted when i bought boat iwant to sand and recoat bottom,what grit paper should be used 100 150 200,and steps aft to recoat.
  18. C

    steps to pulling 4.3 out

    i just ordered a 4.3 from rapido,it will ship in a week or 2,i need to pull my 4.3 out,i know i am going to need a good hoist no problem what are the first steps ,i can take some parts off while the motor is still in,what other parts must be disconected be fore i can hoist out,i will pull out...
  19. C

    The blues are running in ri bay

    every year around this time blue fish begin to take over upper bay areas,this yr their a little late due to the ri water being so warm,1 or 2 weeks you can go out and chase the scools ,just look for birds and bait fish jumping almost into the boat,and they give a great fight to,keep your fingers...
  20. C

    4.3 rebuild vs replace with reman.

    my 4.3 makes a loud raping sound athigh rpms,loseing power,i know its time to repower,i like the size of this boat,the hull is in good shape,a new boat this size would cost 30,000 whats the best way to go.::
Top