Search results

  1. B

    Changing suspension fork DP-A help

    i was able to source the suspension fork i needed for substantially cheaper on ebay, its a good condition used one.. but for $300 as apposed to almost a $1000, im all over that. however the info im looking for is what seals i need to replace in the drive and water tube? do they come as a kit or...
  2. B

    98 5.7 GSi started to de-winterize and wont start...? fuel problem

    here goes guys. 98 5.7 GSI. just the other day i went out to start getting the boat ready for use, after i reconnected the batteries, and changed the fuel filter it would just crank...but will fire with starter fluid, the boat has fresh good gas, oil/filter and fuel filters were changed before...
  3. B

    Specific winterizing questions 5.7 GSI/ DP-A

    this is my first time winterizing this boat so im just looking for assurance that im doing it right..so far i have treated the fuel system, fogged the motor, drained the manifolds, disconnected my raw water pump( Engine is closed cooled) used compressed air to blow out the remaining water in the...
  4. B

    help with suspension fork replacement! DP-A

    im in the process of replacing my broken fork, i ordered all the seals i will need to replace and the fork, i started disassembly of the drive and i have the upper gear off, and i dont know if the intermediate needs to be removed from the lower? and if so how does the rest of this come off? ive...
  5. B

    Broken suspension fork...is it a saftey thing?

    This weekend i had a little accident which is upsetting, but im going to buy parts and fix asap! my DP-A suspension fork cracked in half at the top by the water inlet and at the bottom as well, what happened is after sitting in a cove for awhile i reved the motor a few times and the third time...
  6. B

    Help with Trim Sender, DP-A/ aq271c

    i know my trim sender is bad i have one in the mail coming this week, i recently replaced my trim pump,motor and hydrolic lines with the updated style with the white plastic reservoir, its works much better, and doesnt leak down, iin my efforts of fixing the old one i found four little swiches...
  7. B

    ATF4 in trim system? Ok to use?

    Yesterday i put atf+4 in my reservoir. Does it matter. Or should i use dextron. It has not been mixed. Just full with atf4
  8. B

    Whats it worth!?

    Selling my volvo sx-m drive unit as a whole. Has 100 hours on it., perfect condition. Just wondering what these typically sell for. I have it listed for 2000. And have had several calls. Is it worth more is the question! Thanks guys!
  9. B

    What is my trim fin for? DP-A

    I found a trim fin that attaches to my outdrive but what is it for. It has never been used on my drive since new. It just sat in the glove compartment all these years. The drive has a plug in in were the fine would go. Im just curious what its for
  10. B

    another tach issue...

    i jusr recently repowered from a carbed 350 to an efi 350 and the only thing that is wierd is the tach, i hooked my shop tach to it and the boats tach is about 1100 off (slower)from the shop one,
  11. B

    help me find props please..!

    i recently repowered my boat with a new 5.7GSi pbyc motor, has DP-A drive with a 1.95 ratio, and B8 aluminum props. boat is 21.5 foot Invader 204 elan v-hull. hit 56 mph on a windless flat day at 4800 rpm...i will be double checkin my tachs accuracy today. i feel there should be more speed, my...
  12. B

    More trim help needed, DP-A

    After switching the fluid lines and correcting the wiring i thought the drive would trim up while in motion but it still doesnt, this morning i noticed the drive slowly came down through the night. About half way. This didnt happen when the lines were backwards either. In my other thread about...
  13. B

    Aq271c/ dp-a trim help.

    Took the invader out today and it ran great, nice and cool, good oil pressure, topped out at 64 mph great torque coming out of the hole, however the trim wouldnt come up while driving unless i was would slow down and the hit the throttle again. It goes down just fine, i looked at the oil in the...
  14. B

    5.7 gsi, no water out exhaust on muffs..?

    Before i hooked up the drive i took a hose to the water inlet hose on the outside of the transom shield and it worked great, good flow no temp issues. Today i ran it on muffs with the DP-A, i even taped the muffs for a good seal but they leaked a bit, my hose isnt the most powerful but it didnt...
  15. B

    Invader aq271c/DP-A trim just clicks?

    today i installed my outdrive and my trim tubes werent at the right length to match up so i jumped in the boat and tilted it down, the trim pump came on for a few seconds and then stopped now all the darn thing does is click. maybe solenoids behind relay? fuses..im not sure were they are?
  16. B

    DP-A re instalation questions

    im near completion of my EFI converison in my invader and since i wasnt the one who remover the drive when the last motor went i want to be sure on how it goes on, im waiting on my last part from fedex tommoro moring and it will be ready to go on, i replaced the ujoints on it, and changed out...
  17. B

    Flexplate to flywheel bolt torque?

    AQ271c i cant find that torque spec in the manual. Anyone know?
  18. B

    flywheel cover for AQ series drive.

    EDIT: Please read our rules, bransjeep. Soliciting can get you banned. I hope because ive already started looking, with little luck..
  19. B

    Intermediate Bearing question?

    i have the model that uses 2 bearings in the housing..the parts dealer at Marine Specialties couldnt find the part numbers so i did some research... i believe i need either a # 6007 bearing and a # 6206 or two #6206's can anyone please confirm this?
  20. B

    volvo penta main electrical connector

    what kinds of connectors did volvo use throughout the years? im lookin and cant find mine..
Top