Search results

  1. metsfan3197843

    Sea water pressure sensor

    I’ve gone through 2 sensors in 3 seasons. Can anyone convince me it’s a bad idea to just dummy the sensor out? I keep up with impeller changes and watch the temp gauge. This thing has been more of a nuisance than protection. Both sensors were OEM and not cheap. At the very least I’m going with a...
  2. metsfan3197843

    Trim sender failure

    Troubleshooting erratic sender readings. Found this nice rusty pile of goo and rusted metal. Assuming that’s the issue. My question is, this was a brand new sender I installed last summer. Wondering if I didn’t install correctly and that’s why it failed so fast?
  3. metsfan3197843

    Cabin light lens removal

    Trying to figure out how to get to the lamp inside this style of cabin light. Doesn’t seem to unscrew or just pull off. Thought I would see if anyone has this style before I try any force. Thanks
  4. metsfan3197843

    Sanity check from a parts pro please

    My gear lube monitor bottle has a slow leak from the bottom fitting or wire penetration. I ordered part number 8M0075709 new in the box unopened. My current bottle has the hose barb pointing to the left when viewed from the front of the engine. The one I received has the hose barb pointing to...
  5. metsfan3197843

    MPI vortex intake manifold

    **edit vortec...... I was under the impression that swapping from a 5.0 MPI to 5.7 MPI requires a different intake to match the different heads. Part 8M0104793 is listed for 5.0 5.7 and 6.2 on multiple parts sights I’ve looked at. I’m confused what do the pros say?
  6. metsfan3197843

    Power steering issue

    when pulling up to the dock today I had a moment of panic as I had the wheel turned all the way I believe to starboard (can’t remember as panic set in) and the steering bound up and I couldn’t turn the wheel. I gave a little force but no go. I quickly grabbed my boat hook and got a cleat on the...
  7. metsfan3197843

    Used Bravo 3, what to look for?

    going to look at a used Bravo 3 a guy has had on a pallet in his shop for quite a few years. It was from an outboard conversion which I believe as it comes with everything from inner transom plate to props. 500 bucks seems like a good deal. Just want to be sure it’s not toast. Besides pulling...
  8. metsfan3197843

    MPI low pressure pump

    I have read that the low pressure pump is not needed and that the engine will run fine on just the high pressure pump. Tracking down a fuel pressure drop to nothing on my engine I discovered a bad connection on the booster pump and it was not coming on. Fixed that and took the boat out and now...
  9. metsfan3197843

    Bogging and wild tach question

    left the dock today and after motoring through the no wake zone and letting the temps come up and stabilize I dropped the hammer to get up on step. As I was ramping up I noticed the tach going crazy and then the engine bogged down and I shut it off but it would have died on its own. I assumed...
  10. metsfan3197843

    Water distribution housing delete

    has anyone come up with a way to replumb this plastic hunk of crap? I have the air actuated one on full closed cooling. On my second one and the drain plug is leaking. It gets much worse if I really tighten it so I’m assuming the POS plastic housing is cracked yet again. Thanks
  11. metsfan3197843

    Major water in the fuel system

    Motor started vibrating and coughing. Emptied fuel separator that I just installed and it was completely full of water. This was the first start up of the season. Ran fine for the 5 minutes of fresh gas I put in the filter when I installed it. I plumbed a 5 gallon outboard can in and installed a...
  12. metsfan3197843

    Distributor cap screws

    Misplaced the 2 screws that hold down the distributor cap. T-20 torx head mercy part number 10-884786. Can’t seem to find any info on what thread pitch they are so I can buy a couple new ones. Anybody know??
  13. metsfan3197843

    New exhaust elbow questions

    Got my new OEM elbows today. They came with the plug uninstalled. It appears to have a red sealing or loctite compound on the threads. Do I need to use anything on the threads when installing or are they ready to go in as is? Also need to pick up a couple 3/4-14 to hose barb fittings for both...
  14. metsfan3197843

    Bravo 3 sea water pump inlet hose

    looking to replace me hose from the inner transom fitting to the inlet on the sea water pump for my bravo 3. OEM part is well over 100 bucks which seems crazy for a short section of hose. Is this just rubber hose or radiator hose? Seems like it can be just bought locally from bulk. OEM part...
  15. metsfan3197843

    Oil monitor hose to bell housing

    Finishing up transom kit rebuild and only have the oil hose to bell housing connection left, it’s kicking my butt. Any tips? I have not driven the uni bellow sleeve on yet so I can pull the bellows out of the bell housing. Not sure if that will help ant though....just a blind stab with a tight...
  16. metsfan3197843

    Help with fuel separator bracket

    I tore down my 5.0 MPI for some rust clean up and painting. I have a bracket that seems to not connect to anything and I guess I didn’t get a good pic on tear down... I drew in a filter for reference 😁
  17. metsfan3197843

    Drive shaft spline/coupler grease

    quicksilver products are not readily available where I live. Is there a suitable alternative to use to grease the drive shaft splines and to pump into my newly installed coupler? thanks
  18. metsfan3197843

    Broken oil pan bolt removal

    in the process of changing out my rusted out oil pan one of the bolt heads sheared off like butter. Tried vise grips. Any suggestions??? thanks
  19. metsfan3197843

    Cleaning up rust on motor

    Finished removing the wiring harness off my motor today to get a look at the rust damage from a leaking engine bay hatch. Intake has some pretty good corrosion in the well by the distributor and the port side valve cover is pretty rusty. Not sure how to determine what’s salvageable and what’s...
  20. metsfan3197843

    Glad I pulled my engine

    Was a little hesitant to pull the motor just to clean things up and look things over but I’m glad I did. I could poke my finger through if I pushed real hard🙈
Top