Search results

  1. B

    1997 4.3l penta seized??

    I just acquired a 1997 4.3L penta that hasn't run in 10 years. I'm going through the motor to see if its worth messing with. i haven't tried to start the motor mainly because the batteries are dead. Just wanted to make sure it wasn't locked up. I pulled the plugs and removed the belts and...
  2. B

    No warning buzzer

    The warning buzzer does not sound when the key is in the run position. It sounds only for a short time when the engine is turning over. 2001 5.7 lt ol654116.
  3. B

    Do I need a special tool for this

    I am replacing my shift cable and bellow. I cut the old one out so I could put a socket on it. Now I need to know how to Retighten the new cable. It has a long plastic tube on it that the cable feed through. Is there a special tool. I am having a hard time up loading a photo Alpha1 gen2 Ol850536
  4. B

    Shift cable bellow replacement

    Do I have to remove the bellow housing to replace the shift cable bellow. Also do i need to have a hinge pin removal tool. ol850536
  5. B

    A noise from the back of the engine 5.7 Alpha 1 Gen2

    First day out after replacing gimbal bearing, U-Joints, and coupling assembly. It ran great at idle when I tried to get up on plane a roaring sound started to come from the back of the engine it sounded like sand paper on a turning piece of metal. When I backed it off plane the sound went away...
  6. B

    Alpha 1 GEN 2 Shims

    I have been working on my out drive for several weeks. Replacing bearings and u-joints?. While looking at the mercruiser manual I see shims between the bearings and the gear drive assembly, while taking it apart I did not notice them. Then tonight I see them on the ground by the work bench...
  7. B

    U-Joints Alph 1 Gen 2

    I am replacing the U-Joints on my outdrive. From my previous tread I asked if automotive U-Joints would work and was told yes and given some part numbers. I went to CARQUEST gave them the numbers and they cross referenced with 1-6300 (Carquest brand) They also measured the old ones and they...
  8. B

    MerCruser selants

    I have installed new bearing and retainer ring in my out drive(OL850536). In the shop manual it call for 2-4-C Marine lubricant with Teflon, to be placed in the Oil Seal. Is this necassary or will any good quality lubricant with Teflon work.
  9. B

    out drive shims alph1 gen 2

    I have removed the retainer ring from the drive yoke once i had all the parts layed out there are no shims in there. and they are in the pic in the mercruiser manual do they need to be in there. Do i need to get new ones to replace them. Alpha 1 Gen 2 ol850536
  10. B

    Alpha 1 Ujoints

    I removed my outdrive today and I have ujoints with inside keepers. According to the manual the retainer nut needs to come off in order to remove the shaft to press out the old ujoints. I bought the special too to remove the retainer nut. Any advice on what to do after I remove the retainer nut...
  11. B

    Alph1 gen2 gimble bearing is tapping

    I have burned up 2 gimbal bearings one with less than 1 hr. on hose in the yard. This last one started out as a slight clicking noise from gimbal area then became a knocking sound the longer I ran it approx. 3-5 min. I have used an alignment tool which slid in and out with ease. Thanks for any help
  12. B

    2007 70hp Yamaha idles rough and has no power

    The motor sat up for 6 months. It is a bit cold natured and when it does start it idles rough and will bog down when under a load. I poured out the old gas added fresh. When I sprayed carb cleaner in the carbs, especially the bottom carb it seemed to clean up but gets rough again. Any help...
  13. B

    Raw water pump

    I have a 5.7l mercruiser alpha 1 Gen 2 with a new style raw sea water pump. I worked great a month a go. Put it on the hose in the yard no water through the pump. Check all the hoses for clogs, found none. Replaced the impeller still no water. I even put the boat in the water thinking low...
Top