Search results

  1. brinker232

    1990 Force 150

    I have a 1990 Force 150 on a 20' Bayliner. The boat is finally beyond economical repair but the motor still runs amazingly. It will put the boat around the lake about 45 mph with 4 people onboard. I am going to part out the motor and have the rest of it hauled off. If anyone needs anything off...
  2. brinker232

    1990 Bayliner Decal and Pinstripe Removal from hull.......

    I have a 1990 Bayliner and I am trying to remove the old pin striping and the decals. What is the best way to go about this with out causing damage to the hull? I will not be replacing them with anything other than a good polishing! Any and all tips/tricks are greatly appreciated!!
  3. brinker232

    150 hp Force Fuel Carb Question.......

    Is it normal for the carbs to "Spray" or "Mist" fuel out the front of them when idling?
  4. brinker232

    Deleted

    Deleted
  5. brinker232

    150 HP Force falling on it's face after about 1 min wide open.........

    I have a 1990 Force 150. It runs great through all spectrums of the throttle range except wide open. After a minute or so it starts cutting out and will eventually drop down to an idle after a minute or so I can nail it again and it's fine. It's almost like its overheating or something but I...
  6. brinker232

    Water Droplets on Spark plug

    I pulled my plugs out today and had one that had a few tiny water droplets on it. Looked like condensation..... Any thoughts??? Thanks!!!
  7. brinker232

    Checking/Adjusting the Timing on a 1990 150hp Force

    I broke a piece of the Throttle linkage over the weekend while I was trying to raise the idle. I got a new end piece but I took the shaft and other end off for cleaning before I realized that this arm tied the timing advance and the Carb positions together and have to way to "reset" it to the...
  8. brinker232

    1990 Force Throttle Question.......

    I have a 1990 Bayliner Capri. My previous boats have all had a separate lever to raise the throttle while it is still in Neutral. This boat doesn't seem to have this, if it does I have no clue how to do it, and I am having hell getting it to start with out flooding it since it is idling too low...
  9. brinker232

    150 HP Throttle Linkage Parts

    I need help locating this broken part. I'm holding the plastic linkage end that broke. Anyone know of a parts schematic with numbers or a place that I can order these? Thanks
  10. brinker232

    1990 Force 150 HP Lower Unit Seals

    I changed the impeller yesterday and had a bunch of milky lower unit oil. My screw gaskets were bad last time I checked the oil (about 2 weeks ago) so I used o-rings instead. This time I re-used the o-rings but also used teflon tape on the threads. Where can water get into the gearbox but the...
  11. brinker232

    Force Primer System

    Can someone please explain how the Primer System works on a 1990 150 hp outboard with 3 carbs? Where does it get the fuel from, the top carb bowl?
  12. brinker232

    Force 150 Idle too high......

    I have a 1990 Force 150 and it seems to be idling too high. I can't get it out of gear some times. I believe that I have adjusted the throttle cable all that I can and it still won't come all the way down without me physically closing the throttle butterflies all the way. I've lubed all the...
  13. brinker232

    Who all has a Force 150 hp CFI motor??????

    Just curious to see how many others on here have a 150 hp Force outboard.
  14. brinker232

    1990 150 HP Force on a Bayliner Tilt/Trim not staying up

    When I trim the motor all the way up it will be all the way back down in less than 5 minutes. When in the water I am constantly having to trim it back up every min or so. Any fix for this?
  15. brinker232

    Adding a Tell Tale to a Force 150

    I grew up with all of our outboards having tell tales, tell tails, pissers, etc. I have a Force 150 that does not have one. Any opinions on installing one? a kit? directions? locations to install it? I would just like to be able to look back and know the pump is working properly. Thanks!
  16. brinker232

    Inherited a 1990 Force 150

    I have been reading the forums here and on other sites and see that there are many who can't stand the word Force while actual owners seem to be happy with them. I am trying to get this thing running to have some summer fun with the kids until I can put a Mercury in it's place. I need help with...
Top