Search results

  1. B

    Motor Guide Xi5 route issues

    I wanted to share this information with you if anyone is having trouble with the route feature on their Motor Guide Xi5 with pin point GPS. Everything works on mine except the route feature. I contacted tec. support, and they said there is a known problem, and their engineers are working on...
  2. B

    Motor Guide shaft replacement

    I am replacing the shaft on my Motor Guide ix5 trolling motor. What would you recommend using on the threads of the shaft to keep the water out of the motor. Thanks...
  3. B

    charging trolling motor batteries

    My trolling motor is 24 volt, is there a way I can charge the batteries with a battery charger without having to remove the cables from the batteries and charging them separately? Thank you...
  4. B

    Exhaust manifold bolt torque spec.

    What is the torque spec for exhaust manifold bolts and for the riser bolts on a 1993 4.3L Merc. cruiser? I appreciate anyone's help. Thanks...
  5. B

    manifold bolts

    I have a 1993 merc. cruiser 4.3L I have to replace the manifold on one side and I am afraid of breaking the bolts. I have applied quite a bit of pressure to the point I am afraid they might break off, so I quit before I snapped one off. Any suggestions? I appreciate anyone's help. Thanks...
  6. B

    Auto start assembly

    I have a 1999 50hp 4-stroke (Model#50ELPT4S) (Serial#0G773202) Motor runs great but starts hard when cold. Is there a test procedure to test the Auto Start Assembly (Electro Thermal Plunger) part#825106T Also is there a way to test the Solenoid Coil part#97685T I would greatly appreciate...
  7. B

    lower cowl removal

    Have a 2019 evinrude 75hp e-tec How do i remove the lower cowling so i can replace the bottom spark plug. Thanks...
  8. B

    Idle adjustment

    I have a Johnson 40hp (Model# J40ELEOD) (Serial# 03743175) It idles a bit to low, I would like to adjust the idle up just a bit. How do I do that? I appreciate your help, thanks...
  9. B

    fuel pump cover

    I have a Mercury 18hp (18XD) 6533678 my question is the fuel pump cover has 5 screw holes and one hole in the middle of the fuel pump cover, when I pump up the primer bulb so it's hard, fuel weeps out the center hole. Is this normal? Thanks for your help...
  10. B

    no power to the starter solenoid ferminal

    2006 Johnson 9.9 4-stroke Model # J10TE4SU Serial # 22038604 The small wire that goes to the starter solenoid terminal has no power to it, that is why the starter won't turn over. The neutral switch checks out ok, and the fuse is ok. Any ideas? Thanks...
  11. B

    1975 Evinrude water outlet

    On a 1975 Evinrude (15504C) (E0002898) where does the water come out? I do not see a outlet tube anywhere. Does it exit through the exhaust? Also where do you unhook the shift rod so you can remove the lower unit? Thank you for your help...
  12. B

    Old Johnson 25hp year & oil mix

    Could someone tell me what the oil mixture should be and also the year of the motor. Model#J25RCIM Serial# E5434309 I appreciate your help, thank you...
  13. B

    What year is my Honda 8hp

    Could someone tell me what year my Honda 8hp is? Model # BF8A Serial # BACS-1206284 I appreciate your help, thank you...
  14. B

    Johnson 40hp starts then quits

    I have had other posts about the problems I have had with this motor and I would like to update. I have a 1995 Johnson 40hp (Model# J40ELE0) It has a new stator and cdi and a new primer solenoid, new plugs. Now the motor will start every time I hit the key, but runs only a second or two. I...
  15. B

    Weak spark

    I have a 1995 Johnson 40hp Model # J40ELE0 Serial # G03743175 following up from another post, with the plugs installed in the motor the spark gap is less than 7/16" it's more like 1/8". The compression is 180lbs. per cylinder, have fresh fuel, new plugs, flywheel key is good, battery is 13.36...
  16. B

    Johnson 40hp won't start

    Older Johnson 40hp, Has 180lb compression each cylinder, has two new plugs, fresh fuel, and has super good spark. Will not start, pulled the plugs, squirted fuel into each cylinder, reinstalled plugs, won't even fire, nothing at all. I appreciate your help. Thanks...
  17. B

    power trim pump problem

    I have a Mercury outboard with a Electric Hydraulic power trim and tilt system. The electric motor runs in both the up and down directions but the unit does not raise the motor in either direction. I pulled the electric motor unit off to make sure the hex pin between the motor and pump was not...
  18. B

    1974 evinrude 2hp no power

    Well here I am back again. Got the spark problem fixed, now the motor has no power. Starts right up, when you open up the throttle the rpm's go up but not much above a high idle. I can screw in the high speed jet all the way in and it makes no difference the motor runs the same. I did clean...
  19. B

    No spark

    1974 2 hp evinrude ( no spark) new coil, new points, new condenser, new plug wire, new plug. Points set at 20. Made sure the points are not grounding out to the timing plate. Even though the coil and condenser are new I tested them just to make sure. Any ideas? I appreciate your help...
  20. B

    1958 Johnson 35hp seahorse (Model RDE-19)

    The faceplate piece that goes on the front of the air intake that the hi and low speed needles pass through and the choke pull knob passes through, there are two springs that slip over each of the needle jets, can anyone tell me how they go or show me a picture of how they go? I'm not sure how...
Top