Search results

  1. C

    1962 evinrude fastwin 15036 fuel issue

    I have been posting about this motor lately.I had it running great.I have had it in the drum cranking it for 5 days.This morning it was hard to start and not running right.I checked the bulb and it would not stay firm.I then checked the tank and it was almost out of fuel.Its a 3 gallon tank...
  2. C

    My new project.1972 johnson 25e72r .

    This motor ran 3 years ago.I used it a long time.When cleaning the carb 2 screws that hold the bottom bowl on were gone .Both on the same side.I have a 71 20 hp that is basically the same looks wise .I robbed 2 screws out of this bowl.The carbs looked the same.What is the difference The carb...
  3. C

    Evinrude 1972 18 hp fastwin not pumping much water

    I just got this running . I put a new impeller in it.it is pumping a little water but not much.I think there was a rubber boot that the water pump tube slid into that if I remember correctly did not look right.I am going up to the shop to remove the foot.Do I need to blow compressed air in the...
  4. C

    1962 evinrude fatwin 18hp carb settings.

    The high ,low and other jet
  5. C

    1962 evinrude fastwinn 18 hp.Which fuel line goes to the pump?The one close to the block or the ot

  6. C

    1976 collins craft.I have the boat off trailer and upside down.It has been washed with muritic acid.I am going to sand with 80 grit and use 2 part

  7. C

    1976 456hh 45 hp.magneto model

    The top plug quit firing after about 1 hour run time.I replaced both plugs with new ones and it happened again.I installed one of the used ones that I had cleaned,while on the water ,top cylinder again.The plug looked good both times what would cause this.Motor has set up for years .My dad...
  8. C

    Yamaha foot rebuild

    my friend hit a stump ,broke a tooth on the forward gear.2006 75 four stroke.I rebuilt the foot.In the vise it shifts into all gears.When we try to install it on the powerhead it will not bolt up unless the shifter is in reverse.At this point the gearcase is in neutral ,the throttle at the helm...
  9. C

    Evinrude cowl seals

    I need one for a 1976 evinrude 40 hp.These are no longer available.I have several vintage motors that need these.Are there any aftermarket seals that will work
  10. C

    70's coil

    Will the green coils off a 70's 85 hp work on a 1976 40 hp.I know the connectors will have to be cut off and spliced.How can you check the cylinoid
  11. C

    70's coil and cylinoid

    Will the green coils off a 70's 85 hp work on a 1976 40 hp.I know the connectors will have to be cut off and spliced.How can you check the cylinoid
  12. C

    Evinrude te60tlene 92 60hp miss

    buddy of mine is having problems with this motor.cleaned carbs new fuel tried 2 different tanks took coils off running motor no different compression 98 96 92 new plugs could this need a head gasket this compression seems low with my guage
  13. C

    1984 evinrude 15 up e15ecrm

    When button is pressed nothing happens.Itookstarter off and hooked it to jumper cables it works.I took push button apart and cleaned contacts still nothing.Help
  14. C

    suzuki dt 30c 1989 model 2 stroke

    When I got this motor the carbs were missing.It has a new thermostat and water pump .It is loosing rpms and the red light comes on.I do not think the oil injection is working so I am mixing it in the gas.How can I disable the oil injection to stop it from loosing rpms.Also the warning buzzers...
  15. C

    suzuki dt 30c 1989 model 2 stroke

    The red light comes on and I am loosing rpms.It has a new thermostate and is pumping water.Ido not know if the oil injection is working . I am adding oil to the gas. How can I disable oil sensor so I can check and see if this is the problem.Igot this motor with no carbs on it and the warning...
Top