Search results

  1. A

    Engine warning light Evinrude Ficht RAM 2002/2003

    I have bought what should be a Evinrude 115 Ficht RAM complete powerhead with all components. It must be a 2002 or newer, since it has a newer oil lift pump than the pre 2002. When I tried to fire the enginge up today, it shut down after some attempts, and the third warning light on the system...
  2. A

    Oil injector/manifold routing Evinrude Ficht RAM 90 hp 2003

    Hi I have swapped my 2000 90 Ficht RAM with an 2002 or 2003 Ficht RAM. There is the newer oil distribution system, with one more oil pipe connected to the oil mainfold,. I guess four of them are to each cylinder, but unfortenately the previous owner cut the pipeline that runs under the fuel...
  3. A

    Change from internal to external oil tank Mercury 2-stroke 90 hp 1995?

    I wonder if the oil pump on my Mercury 2-stroke 90 hp 1995 will manage to pump the oil up from an external oil tank? Then I will get rid of the traditional leakage from the top of the tank when the motor is tilted. Does the gravity in the integrated tank have some effect on the oil flow, or wil...
  4. A

    Sneezing at idle when starting after 30 min pause

    I have an odd idle-problem with my 150 98`Ocean Pro. It starts and runs very well at idle and full speed when motor is cold. When hot, it also starts and runs good at idle and full speed. BUT; When motor have been shut off for 30 min, it is impossible to run well at idle. It starts, sneezes and...
  5. A

    Props for Sunbird SWL 203

    I have changed motor from Evinrude Ocean Pro 175 to 150 on my Sunbird. The prop on the 175 was a Raker 14 1/2 x 20, the prop on the 150 is an ordinary 14 1/2 x 21+. Which one will be best for my Sunbird SWL 203? I have noe experience on this.
  6. A

    Colour code Sunbird SWL 203

    I am going to paint my Sunbird SWL 203 back to its original colour. Does anyone know the colour code or the name of the white colour for the top coating on this boat?
  7. A

    Colours wiring evinrude ocean pro 159

    Does anyone know where these two cables (with three wires) shall be connected on the dashboard? I know purple is for the ignition switch, but there already is noe in the 6-pin connector to the switch.
  8. A

    Leakage from o-ring fittings fuel pump Evinrude Ocean Pro 150 98`

    I have a leakage from the o-ring fittings on the top of the pump into the fuel bracket on my 150 Ocean Pro 98`. It starts to flow at once when I try to start the motor. It is not possible to get the hand pump hard, the gasoline will just flow. I have tried to put on new o-rings, but the problem...
  9. A

    Can I use the same VRO pump on an Ocean Pro 94` 175 and 98` 150?

    I have bought an 98`150 Ocean Pro where the VRO pump was disassembled when I bought it. The problem is that I can not see how the fitting on the fuel outlet shall fit into the bracket. It is turned 90? compared to the fitting on my 94`175. On the BRP parts list, it should be the same fuel...
  10. A

    No spark Evinrude Ocean PRO 150 98`

    I have lost the ignition on my Ocean Pro 150 98`. I am not very good at electronics, but have done some testing with an ordinary multimeter. I have done as follows; Stop Circuit test. Separated the 5-pin connector between the stator and the powerpack. Still no ignition. Testing the grounding...
  11. A

    Evinrude 175 Ocean Pro submerged 12 years ago... A look inside

    I have started several threads regarding this motor, according to the previous owner, the motor was submerged in 2003. I do not know what was done then, but I know that it has been in use for several years after that. The motor had not been in use for three years when I bought it. I have...
  12. A

    150 Ocean pro 1998 at idle rises to 3000 rpm and stalls

    I have bought an 150 Ocean pro 1998 that had this problem; at idle it increased to 3000 rpm without moving the throttle, and then stalled. But now, there are no ignition at all. The carbs had been checked before the no ignition-problem, according to the previous owner. Could this be problems...
  13. A

    Optimax 150 2000 model running on three cylinders

    I am considering bying an Mercury Optimax V6 2000-model. The compression is good, but it runs only on three cylinders. I have searched the forum, but have not found anything about this. Has anyone a quick fix, or should I avoid the trade?
  14. A

    Compression differences Ocean Pro 175 1994-model

    I have bought an Ocena Pro 175 1994-model that previously has been under water (over ten years ago). The previous owner says that he has used it several years after that, but it has not been used the last three years. I have not been able to start the motor, and have started with changing the...
  15. A

    Removing the flywheel covers Evinrude 175 Ocean Pro 1994 (carburated)

    I have to remove the flywheel covers of my Evinrude 175 Ocean Pro 1994 (carburated) to repair the bendix drive. (It is no doubt that I have to take it out). I can`t find anything about removing these covers in the manual, but have understood that it is a bit tricky. Does anyone have any advice...
  16. A

    Starter just spins, not engaging the bendix drive, 12,6 V to the starter

    I have bought an Evinrude Ocean Pro 175 hp 1994 model that has not been in use for three years. I have changed the starter, but it only spins, it will not engage the bendix drive. The large, lower toothwheel of the bendix drive did not move when I took out the starter, so I sprayed some WD40...
Top