Search results

  1. C

    1662 prop pitch?

    Hi Everybody, Can someone help me id this propeller it has 1662 on it seller says it came off 1985 125 HP Force what pitch is it and will it fit on 1989 125HP? it has 15 spline same as my '89. Thanks, Paul
  2. C

    Exhaust gasket source

    Hi Everybody, Like to replace my exhaust gasket on my '91 120HP force motor that's the one ties into the lower cowling if it's not available is high temp silicone the way to go for repair I have a gasket it has been in question about leaking and causing the motor to not idle correctly when the...
  3. C

    Seaalind crankcase parting Line

    Happy Easter Everyone, I'm in the process of putting back together my '91 120 HP Force and I have no grooved crankcase for the seal to fit into. What I had when I took it apart was thin coating of RTV and I don't think it was the Permatex 51813 that I've read about on searches can anyone...
  4. C

    120 HP Smal Gouges in exaust Port/clylinder

    Hi Experts, looking for a educated opin,on how bad is this gouge I was thinking I could radius these little gouge without major reboring but would that effect the timing? Any input valued . Thanks, Paul
  5. C

    '91 120HP Lower Unit

    Hello fellow wrench pullers, I need to change my '91 120 HP l/u out, I have a 125 Hp U.S Marine I believe a '89 everything is the same except 120 is two piece driveshaft however there are slight differences on the height of the two waterpump outlets the older style waterpump is about 1/2"...
  6. C

    What is this hole in the lower unit

    Hi, Tonight I'm in the process of preping for paint 1961 40 HP Lark 3 and found a hole being plugged by silicone is this someones attempt to seal a corrosion hole or is this supposed to be here it was drilled out with a 3/16" drill bit any help is much appreciated. Paul
  7. C

    Differences in '61 Evinrude models

    Hi, Quick question what is the difference between the Standard 1961 40 hp Evinrude and the 40 hp Lark 3 Evinrude? Thanks, Paul
  8. C

    1961 Lark shift lever adjustment on engine?

    Hi, Got a 40 HP. Lark that after it's warmed up kicks out of gear along with shutting down altogether I've replaced the thermostat,waterpump impeller but one thing at a time with this post as it makes it easier to follow I noticed that at the shift linkage close to the block it's slotted for...
  9. C

    Chip in water jacket

    Hi again, this time after running my '61 Evinrude 40HP Lark notice water coming out of lower spark plug hole sludge in my garbage can. My guess was a blown headgasket I was correct when I pulled the head off I saw at the 1 oclock position on the bottom cylinder a broken gasket (the compression...
  10. C

    1961 40 HP Lark 3

    Hi everybody got a couple quick questions I've done a couple searches kinda came up semi empty anyway When I'm idleling / flushing setting low idle cleaning out my engine in a garbage can does that little hole on the starboard side going into the waterpump impeller need to be underwater when in...
  11. C

    Steering Arm Helllllllllllp!!!!!!!!!!!!!!!!!!!

    Hey guys&gals I working on a old wooden boat that has a bell crank steering I need to link it to a 1957 35HP. Johnson the motor has a 1/4" hole with notches in the center I guess this is a standard hook-up but I know very little about where to go for some guidance except your vast knowlege base...
  12. C

    Long to Short 1957 35Hp Johnson RDE-19M

    Hello again this is the captain, sorry, I just had to do it. Anyway I was using the search and saw that some times you have to remove the power head for conversion Is this true with my motor going to a long shaft.couple questions what is involved here I'm buying a book probably Seloc shortly so...
  13. C

    1957 Johnson 35HP Cowling

    Hello everyone, I have question for all you aces out there I have a RDE-19M are all cowlings :D the same for that HP and year? and also where can I buy a new cowling gasket/seal or is this a laughing matter. Any help would be appreciated. :D
Top