Search results

  1. O

    70hp needs choked to get to WOT

    1976 Evinrude 70673D Finally took it out on a small deep pond locally to try it out. starts fine...put into gear and runs a little rough..throttle and would die if I did not hit the choke a few times..and then runs fine at higher speeds. Slow down before I can get to full speed (smaller pond)...
  2. O

    I have to take my gas tank out

    I have a Dyna-Trak 196 SS. The bilge pump does not seem to be working right and when I opened the access to where it is supposed to be, I could not figure out what wiring was what. Let alone the fact it looks like someone before me tried to rewire parts of it. Anyways, I can't get to where I can...
  3. O

    J200STLCDR Compression Test results

    V6 200hp. J200stlcdr I checked compression on all 6 plugs. Looking at motor from standing behind back of boat...Left side is from top to bottom 120...112...112 Right side from top to bottom 100psi on all 3 I am not for sure if that is acceptable or not?
  4. O

    1988 Dyna-trak 196 ss

    I did some work for this 1988 Dyna-Trak 196 SS boat. I know the guy well, so I trust the boat is okay. The boat is sitting about 60 miles from me here in INdiana...only 22 degrees right now. I went by there the other day to see it..one day job in that area...and it was ALL wrapped up in a heavy...
  5. O

    I think my prop is spinning backwards

    I have a 70hp Evinrude 70673D 1976 I am waiting for some idle jets to finally get this thing out of the tank and into the water. When running in the tank to set pick up timing, going over in my head what size jets to use, (Boyesen reeds), I thought that the water was going the wrong way while...
  6. O

    Powerpack?

    70hp Evinrude 70673D...120 on all 3 cylinders (before warm up) I have new pistons, rings, rectifier, coils, fuel lines and tank, spark plugs, fuel pump, rebuilt and cleaned carbs many times, rejetted per Boyesen reeds recommendations , no water leaks, do not see any fuel leaks. rebuilt...
  7. O

    water blowing from bottom plug

    70673D 1976 Evinrude 70 hp Excited to try my rebuilt engine. Bored .030 over. new pisons , rings..gaskets..seals... Cranked...started....died... Thought the starter was bad (smoking from trying to start). Took out the plugs and grounded the leads....mist of water....very definite....blowing...
  8. O

    torque for exhaust and bypass cover

    My first total rebuild. 1976 70hp Evinrude 70673d. My Seloc manual gave me the torques for some stuff but not others. Not sure why. Does anyone know the torque for the exhaust and bypass cover bolts? Thank you
  9. O

    Are there bad Powerhead rebuild kits?

    My block just got done at the machine shop. Not knowing how much they were going to have to take off the cylinders, I waited to order the rebuild kit. Turns out , it is .030 over. While I was waiting for it , I got online to check prices....big difference from one to another. I was wondering...
  10. O

    1976 70hp Evinrude

    1976 70hp Evinrude . 70673D I have put many dollars and hours into this. I have cleaned carbs many times with new rebuild kits. New impeller, new fuel pump, tank, fuel lines, spark plugs, capacitor, all 3 coils, tested stator, trigger, powerpack. rejetted with new boyesen reeds,... I always...
  11. O

    1990 Sunbird boat

    I was just given a boat...1990 Sunbird. The title does not have a model. From pictures I've seen it looks like a Barletta 204 with a 120hp Evinrude outboard. I have not pulled it to the house yet,and I am kind of concerned because this is much different than my other boats....and am not for sure...
Top