Search results

  1. Mikered3500

    1988 30hp - midsection to case bolt tourque

    Hello guys. I am replacing my mid section on my 30hp and can't find the torque specs/sequence on the bolts that mate the midsection to the bottom of the block together. Any help would be appreciated! Thank you
  2. Mikered3500

    25 hp no spark

    Hey guys. 04 Johnson 25 horse not getting spark. The top cylinder is intermittent with a weak spark and bottom has no spark. New plugs in it and I checked the wires from the coil packs. Any idea which direction to go next? Thanks!
  3. Mikered3500

    Boat weight capacity

    Sea ray amberjack srv 200. Capacity plate is missing and I need to order another one but sea ray doesnt have the information I need apparently How do I figure out the correct weight capacity to put on the plate? Thanks!
  4. Mikered3500

    1975 searay amberjack srv 200

    Hey guys. First time doing a major repair on my boat. Im replacing the floor and whatever else under it is needed to be cut and pulled out. The boat is a 1975 sea ray srv 200 amberjack with an outboard. I have already removed the floor (took about 30 minutes) and realized the rot was much deeper...
  5. Mikered3500

    Bottom paint

    So i bought a '75 sea ray 20 ft center console A few years ago. I think it should be running faster than what it is. It seems to have some sort of rubberized material almost similar to bed liner on the bottom in leu of bottom paint. would this have anything to do with speed? Planing time, fuel...
  6. Mikered3500

    Ocean pro 200

    Hey guys. It seems my 98 ocean pro is not running 100% or starting i should sa . It is a real PITA to get it started for the forst time at the ramp and then the rest of fhe day it fires right up. Normal starting procedure, pump primer bulb til its hard to squeeze, trim motor all the way down...
  7. Mikered3500

    1975 searay amberjack wooden rails

    So the teak wood on this boat is splitting and rotting and coming loose. I was wondering If anybody is familiar with this vessel and what kind of wood I should use to replace it with..or another option I contemplated was just flashing it over after replacing with some kind of sturdy wood so...
  8. Mikered3500

    '98 ocean pro 200 on 21ft sea ray

    What would be a good starting point for prop size for this boat and motor combo ? 3 or 4 blade? Stainless or aluminum isn't an issue Thanks!
  9. Mikered3500

    Wiring diagram for 98 ocean pro 200

    Need a full wiring diagram for this motor. Any help appreciated
  10. Mikered3500

    03-04 fight ram injectio twin motors

    Going to look at twin 225 fichts this weekend, looking for advice in questions to ask and what signs to look for and what not.seller claims they both run but have minor problems. Hasnt responded with what issues yet . I think they are 03 or 04 models.im only interested in them because they are...
  11. Mikered3500

    87 Johnson 175 vro head question

    Hey guys .I had a head on the starboard side that had a water jacket cover bolt snap off and it cracked the little housing that the threads are in and I decided to just replace the whole head and the casting numbers are 332137. Do I have to keep that number or can I use a different number with...
  12. Mikered3500

    175 vro getting hot on port side

    Runs fine, just replaced thermostats today, but port side gets super hot to the point you can't touch it within minimin of idling while starboard takes a few minutes to warm up, and when it does I can hold my hand on it without burning myself .any ideas?
  13. Mikered3500

    1987 Johnson 175

    I have a 87 Johnson 175 that has a cracked lower unit, port side of the bullet. Drained the oil out and of course it was milky. Are these LU's easy to find and replace or is it not worth the time to fix it? Motor also came with a bolt in each thermo snapped off. In it. At idle it has a slight...
  14. Mikered3500

    Low compression question

    Hey guys, I posted on here before about this Motor I have on my boat at the current moment. It's a 90-92 (not exactly sure of the year since the I'd plate is missing if it had one) Johnson 225. It used to fire right up when I first bought it in July, took the boat out twice and it's been a PITA...
  15. Mikered3500

    Engine/weight capacity

    Hello, I have aquired a 1975 sea sea 20 foot center console amberjack (I believe it is) .the capacity plate is too faded to read, trying to find an outboard to put on it but I don't know the capacity. Apparently sea ray can't produce any info on this boat...thanks .
  16. Mikered3500

    Etec info

    Hey guys. Recently decided to go in the market for an etec motor. Currently trying to figure out what changes I need to make to my current setup with a 91 or 92 Johnson 225 as far as cables, binnacle, wiring harness, oil or no oil tank needed in the boat or does it have one on the motor itself...
  17. Mikered3500

    2000 evinrude 225 ficht.

    Does anybody have any knowledge on this motor? Found one for sale for 1800...seems cheap but is it worth it . Says it starts up every time but has a "small miss" and needs a wiring harness. He said that's what a marina near us diagnosed it as. That's all the info I know .so the question is...
  18. Mikered3500

    Prop selection

    I put a 14.5x19 prop on my boat this week. Took it out today and was disappointed on the performance. It's a 21 foot Sea Ray center console with a 91 or 92 Johnson 225. The average speed was 10-12 mph at 4500ish rpms depending on waves. What direction should I go in order to get a prop to get me...
  19. Mikered3500

    Fuel gauge.

    Took my boat out the other week for the first time. Filled the tank...or so I thought. The fuel gauge read full at 25 gallons, it's a rds 40 gallon tank...on the water the fuel gauge was jumping all over the place and now it reads below e full time now. I turn the key on and it jumps even...
  20. Mikered3500

    Prop for 225

    Looking for a prop for my 89 225 Johnson .it's gonna be pushing a 21 foot Sea Ray center console. Not really looking for record speed, just something good all around pitch and size. Any help appreciated. Thanks!
Top