Search results

  1. 393Clevor

    1986 60hp Mercury Stator replacement

    got it in boxes and I'm now putting it together.. new stator with a bunch of mounting holes.. not sure which way it goes, does it matter? to clarify, it seems you can mount in any position, you can turn it to the next set of hole and it bolts down ok.. it has two pickups on the stator that are...
  2. 393Clevor

    Is this steam normal.. 1984 50hp Mercury

    I know it's a cold and nasty day and even my van is steaming pretty good.. New water pump has a good stream of water out of the telltale... seems like a lot of steam.. FF to 3.00 minutes Video on the water
  3. 393Clevor

    Trouble shooting these old Mercs

    I watched a video on Youtubes and the guy in the video was showing stator specs he got off I-boats.. I looked around is there a file page somewhere I'm not seeing?
  4. 393Clevor

    85 50hp Merc.. carb rebuild..

    Never seen a spring on the needle like these have.. my question is do I set the float level with the spring removed?
  5. 393Clevor

    I bought it.. 1985 50hp

    300.00 for the boat motor and trailer.. keeping the trim/tilt unit, motor and controls, cutting the rest up.. 105lbs in every hole the wiring looks awesome spark in all the holes, main output shaft seal leaks now that the motor is lowered and the gear oil can reach the seal.. it's got a little...
  6. 393Clevor

    does this look like it had power tilt and trim?

    I messaged the guy a few times still no reply..
  7. 393Clevor

    BTW I got that alternator installed on my 40 Rudy

    Had to messarge it in there but it works awesome.. lol 14.5 after a few minutes of run time.. 35amp don't take long to recharge all my batteries.. It hits the cowling a little but the fish don't care and niether do I.. it works.. got the belt from McMaster Car, 13.00 and the Alt. from ebay 35.00...
  8. 393Clevor

    1984? 60hp power trim/tilt setup?

    Mine doesn't have one... how can I get one?.. anyone ever change one out with a later model.... I got 100.00 in this motor and would like to get power tilt and trim for little to no money so if I can find a donor motor that I can swap out the transom mount or whatever.. that would be great...
  9. 393Clevor

    old 200 Mercury

    is this trim normal that's as low as I can get it..
  10. 393Clevor

    2005 MFS15B2 Tohatsu weak spark

    I just picked this up guy said it would not rev.. checking the plugs they were oily and carbon'ed up a bit one has weak spark nothing on the other.. Been looking around the web and i decided to ask here.. where do I start? one coil and only one side of it sparks that seems like a good place to...
  11. 393Clevor

    I'm back.. lol Voltage Regulator, 1973 40hp

    my 1973 40hp Evinrude didn't come with one but I got 1961 40hp given to me for parts and it had a generator on it. I got it all installed and I'm looking at regulators.. any ideas on getting one I can mount inside the cowling? are all voltage regulators the same? any ideas how many amps this...
  12. 393Clevor

    water pump upgrade.. 73 Rude 40hp

    So put a new impeller in it.. the wear plate was good, the cover had a nice soft rubber seal that feeds the motor tube.. no heavy wear marks inside.. looked good.. the tube looked good at the pump end of things. no gaskets anywhere there wasn't any when I started and there isn't any now.. it...
  13. 393Clevor

    Tachometer wiring? Not sure..

    I got this with those two 40hp motors, is this something they used on these motors? and it looks like there might have been a resister on the (+) side that has crumbled away.. any ideas? I love the looks of it.. old school for sure..
  14. 393Clevor

    1973 40hp Rude gear case input shaft install height

    Doing the water pump and it seems the key way for the impeller is below the wear plate.. the key way I took out was notched on the bottom to clearance the plate.. Is there something going on in the gear case I should look at? Tried using the new water pump I got with the 75 J but it's...
  15. 393Clevor

    kill switch, ignition ? 73 40hp

    In the final stages of getting this old girl ready.. I am missing the motor plug part of the controller so I just hacked off the end of the harness coming from the controller.. this is what I have figured out so far... ,where I get stomped is this kill switch part of it.. I got the main power...
  16. 393Clevor

    What would cause this? 1975 40

    was checking things out and found these little buggers.. Ideas anyone.. I changed it out with one from a 74 Johnson this was a 73 Evinrude
  17. 393Clevor

    anyone ever do this?

  18. 393Clevor

    1973 Rudy

    looking for engine cover gasket/seal.. been looking everywhere.. anyone have a place..
  19. 393Clevor

    1989 Force85 Fuel Pump

    I've done the carbs completely and I know they are good but I'm still getting a funny over fueling like thing going on.. Is it possible like some (vacuum operated fuel pressure regulators) to leak fuel into the intake?
  20. 393Clevor

    it's haunted..

    1989 Force85 ran on all three after I reglued the magnet in the flywheel.. got it to the lake and right back to how it ran when I bought it.. changed the coils, moved the coils, no change.. going to replace all the connectors on the trigger wires and try a different cdi box from a 50hp.. Number...
Top