Search results

  1. 2

    alpha one shift shaft alignment issue

    hey there., so i have this gen 1 drive with a shift shaft that when in forward is off by about 1/8-1/4 inch. it just does not line up with the front stud. it is not a full tooth off. you would think this would not be an issue and you can make up the difference in the linkage but that shaft...
  2. 2

    gears make a ratchetting sound after replacing shift/throttle cables, 2010 F150TXR

    hi all, i have this Yamaha f150 that i replaced the cables on because the jackets were split. i installed OEM YAMAHA replacement cables on a Yamaha - Right Side Flush Mount Control Box - 6X3-48206-10-00. the cables are the same in all aspects. now when i start it up, its in neutral and it sounds...
  3. 2

    Does the DP-sm drive prop bearing carrier thrust ring have reverse threads?

    It's been a long time since I've done one of these and can't remember whether the threads were standard or reversed. Had anybody done one recently?
  4. 2

    anyone know what size and thread type the outer prop shaft nut is?

    2000 dp-sm outdrive, i am trying to make a tool and if these threads are a pipe thread, for the inner prop, i may be in better shape than i thought.,
  5. 2

    marina says gimbal bearing was installed backwards?

    so last summer i was visiting a friend down south and helped him with doing his transom rebuild.. we installed a greaseless gimble bearing on a v/p sx assy. the reason being that the gimbal housing was taking on water leaking from where the grease fitting tube meets the housing . the tube was...
  6. 2

    bravo III milky oil but holds pressure for days

    i am trying to locate the cause of the milky oil in my bravo drive. i have had the pressur hold steady at 12, 8, 4 and 14 psi . each pressure held with no drop . ive been working on this for over a week and cant figure out how water got in. im about to just change the drain plugs and gaskets...
  7. 2

    to vent or not to vent, that is the shrink wrap question

    so i have been shrink wrapping boats for a few years now and i always add 2 vents to the job when i am done. it seems like more than 1/2 the boats are very mildew stained come spring when they are opened up. some people add damp rid others do not i can remove the wrap from 2 boats next door...
  8. 2

    1998 50hp carb-can't stop it from leaking

    i have this motor its a bf50a BAZL-2000021 and have rebuilt the carb 2 times and can not stop the gas from leaking from the disc on the side . carb #2, p/n 16101-ZW4-D23 of course this carb is no longer available. im about to through in the towel on this one, i do not know why i can't get...
  9. 2

    2005 5.0 gxi-b belt jumped and wiped out,

    as the title says, the belt jumped inwrad towards the engine and tore 1 rib off it. i read about someone who hadthe bracket for the alternator/p.s pump fatigured and bent but this engine already has the cast aluminum bracket. i replaced this belt last spring(2023) due to squeeling, replacedwith...
  10. 2

    2005 honda bf50 lower impeller housing seal question

    this outdrive cooked the impeller housing and in replacing it, the old lower sectin had 2 seals for the driveshaft and when removing them i found that they are both installed in the same direction. spring side down. now shouldnt they be upper seal, spring side up and lower seal, spring side down...
  11. 2

    looking for service manual info for a 2006 verado fuel pump module

    i have a verado 225hp, serial# 1b546019. the unit runs for about 5 minutes then dies. fuel pressure drops to nothing. i just need a decription of how the module works with the internal float. i have a later manual but it states there is no internal float inside this module so i am assuming...
  12. 2

    2005 malibu with 5.7 indmar manifold issue

    i have to replace the original manifolds and elbow on this boat and the original manifolds are not available or are cost prohibitive. the manifolds it has on it are 531051 and the replacements are 531027 but are about an inch closer to the head which interferes with the dipstick tube. or that...
  13. 2

    5.7 engine serial # ol612162 correct riser gaskets?

    i have this boat that was taken apart before i came along and it has 3" risers. i am not sure which gaskets to use. the parts description shows both open and restricted. is it restricted below and open above?is it all open? all restricted? help please
  14. 2

    anyone have luck with aftermarket v/p fuel pump assy?

    i need a new pump assembly but the 1500 dollar price tag for a v/p pump is ridiculous. this is the assembly with the high/low pump in the same assembly. the one for the mpi engine an bolts to the front of the engine. this boat already had 1 aftermarket pump that lasted 3 years.
  15. 2

    anyone seen this set up before for an alpha 1 gen II system

    i have this boat, 2000 searay w/ 5.0 engine, there is a tee and garden hose coming off it to the back of the transom. looks like a flush out or something like that. i cant see how this will keep the impeller from frying.
  16. 2

    smartcraft system, fuel level fault and no fuel gauge reading

    so this boat is really kicking the crap outta me. 1st the fuel system overhaul now i notice the fuel gauge is not moving. i dumped 25 gallons of gas in it and it has not budged. i cant find any info on how to run a diagnostic on the smartcraft system.
  17. 2

    help, new fuel pumps and pressure still below specs 2004 5.7 MPI

    hi, i have a searay with a 5.7 MPI engine, bravo drive, serial # ow027371, this has the fuel pump under the port side engine mount. i had a problem last season with no power and diagnosed as low fuel pressure, 28psi and 32 with reg unplugged. over the winter i replaced both pumps with OEM...
Top