Search results

  1. B

    40 hp tough to start and smokes too much

    hey guys....i got a 92 or 93 evy 40 hp and the last 2 or 3 times ive had it out its been acting up a bit...its becoming kinda hard to start and smokes severly on start up like its loadin up and floodin out..once running it trys to die and takes some messing with to keep it going but after it...
  2. B

    hydrofoil

    hey guys i just took the stingray hydrofoil off my 1992 40 hp evinrude to see how it performs without it....it is ok to run the engine with the holes unfilled on the cavitation plate where the hydrofoil was mounted?...im getting 27 mph at 5200 rpm with the hydrofoil on...its on a tx 17...
  3. B

    40 hp thermostat

    hey guys i got a 1992 40 hp rude that runs good and i replaced the water pump last month..it really pees the water out. i was just curious if i should put a new thermostat in...i have owned the boat for 2 1/2 years and never changed it and dont know its previous history, but dont think the...
  4. B

    cant get rpms up

    hello again guys, thanks for all the previous help you have given me. i have a 92 evinrude 40 on a tracker tx 17 aluminum bass boat. it has a cmc pwr trim, stingray hydrofoil, and new vortex 12 x 15 aluminum prop. my average load is 2-3 men, 12 gallons gas, 1 livewell full and all my fishing...
  5. B

    whats my next move?

    hello again. ive been trying to get my boat setup right but have run into sum issues.i have a 92' 40 hp 'rude on a 17 ft tracker aluminum bass boat with a cmc power t/t and stingray hydrofoil. with my old 11 3/4 x 17 prop i could turn 4900 rpm. i got a new 12 x 15 vortex prop and can get maybe...
  6. B

    40 hp tach

    hey guys. just out of curiousity i looked under the dash of my boat today. i looked at the back of the tach. it was set on 10 pole. it has 4, 8, 10, and 12 pole settings. is this the correct setting on my tach. my outboards mod # is te 40 elenm. Ser # g 03057836. its a 1992 i believe. thanks for...
  7. B

    prop nut torque

    hey guys. just wondering what the torque spec would be on the prop nut on my 1992 evinrude 40. also i got the xhs hub kit with my new vortex prop. are there any old parts such as washers that i need to reuse? thanks
  8. B

    evinrude 40

    hey guys. ive got a 1993 tracker tx 17 aluminum bass rig with a 1992 evinrude 40 hp on it. right now it has a sting ray hydrofoil on it and its rigged on a cmc power tilt and trim. heres my question. its currently mounted on the lowest of 4 holes and it dead even with the bottom of the boat. the...
  9. B

    is it cupped?

    does anyone know if the standard prop packaged with a 1992 40 hp evinrude was cupped? how would i tell? it ia 11 3/4 by 17.
  10. B

    best prop for 40 hp

    i am running a 1992 40 evinrude on a 1993 tracker tournament tx 17 aluminum bass boat. it is rigged on a cmc t/t, with a stingray hydrofoil stabilizer. im turning 4900-5000 rpm's at at 26 mph at w.o.t fully trimmed out with my 11 3/4 by 17 aluminum prop. that is with my normal load of 2 men an...
  11. B

    1992 40 hp diagram

    can anyone tell me where i can find a diagram listing what each part is under the cowling of my 1992 40 hp evinrude. i have a fuel leak coming out around what i think is the fuel pump selenoid? :confused: can any1 help me out? thanks in advance
  12. B

    1992 evinrude 40 hp wot rpm too low

    ive got a 1992 evinrude 40 hp outboard rigged on a 1993 tracker tournament tx 17. It has a cmc power tilt/trim and an aluminum 11 3/4 by 17 prop (stock i think). i also have a stingray hydrofoil stabilizer on it. im turning around 5000 rpm at 26 mph or so w/ 2 men an all my gear.<br />i was...
  13. B

    1992 40 hp leaking oil near propshaft

    i have a 1992 evinrude 40 hp.recently i have noticed a black goey substance dripping from the L/U. it seems to be coming from the area around the propshaft. it started the last time i went to the lake. all went well ubtil i parked the boat in the garage an noticed the oil on the floor. it wasnt...
Top