Search results

  1. C

    40252E - does it have charger system?

    Its got pull start and a starter . Its a 1972 evinrude 40hp. Was wondering if it has a charging unit and if not how difficult to put one on if possible.. Thanks
  2. C

    70s -- 55hp evinrude - reverse forward issue

    replaced the lower unit.. everything matched up good. Issue is, when put on fw, it goes rv && when put in rv it goes fw.. what could be the problem?
  3. C

    '80 - 60hp johnson rebuild questions?

    i have an engine with low compression, already removed the powerhead, started disassembly. looking to replace gaskets, hone it & rings. Removed the head, reed cage part, looks like connecting rods can be removed from here and be able to take the piston out without taking the 2 crank cases...
  4. C

    55hp - TRL-10R

    i have this motor, was wondering if this can be converted to coil type (car coil type) ignition? not sure if it has points ignition or not. can anybody tell from the model number trl-10r ? there is a "motorola" brand amp. box on this motor, just wondering if its possible to convert to car coil...
  5. C

    how to make head gasket for old outboard?

    i have a old antique evinrude motor, took the head off and gasket cracked. How can i make a replacement head gasket?? its a small 3 inch by about 4 inch.. what type of gasket material can be used to cut something? any tricks?
  6. C

    johnson 55hp - TRL-10R - hydro/elect

    i have this motor that came with a hydro-electric throttle control, (white) with one cable and an electric cable coming out from the front part with a white rectangular connector (that has 3 prongs). Also noticed when I opened up the cover, there is this motorola box (kind of big mounted on...
  7. C

    why not an metal impeller ??

    is this not thought of before to use a metal impeller on the outboards instead of rubber kind that we have to replace over and over!?
  8. C

    what year is this Mariner 25hp? s/n: 721xxxx

    I have a mariner 25hp with s/n: 7219709 ..what year is this?
  9. C

    wiring trim - 3 wire on a 50hp johnson

    how would one wire a trim unit? ie. directly hook it up to a 2way switch? do we need to use a relay or saloneoid?? if a relay or salonoid is required, anybody have a wiring diagram? thanks much.
  10. C

    Wiring diagram for merc 402 / 40hp with s/n:

    Does anyone have a colorful wiring diagram for this motor? S/N: 7060126 // also what year is this? I just got this and all the wiring needs to be redone, stator needs to be replaced, wires corroded, wire insulation basically falls out in your hand.
  11. C

    johnson electromatic shift control - 3 wires from the front?

    I have a control box like the one in the picture, also has a 5 feet wire coming from it from the front with 3 wires to a rectangular white connector, what is that for?
  12. C

    tilt / trim - wiring ? blue / green / black

    I have this tilt trim for johnson, 3 wrire. How do we wire this up ? Believe you require 2 starter solenoids instead of regular 12 volt relays because this one draws too much current not like the 2 wire setup? wires from the tilt/trim: black (ground), blue(believe this is UP), green (down)...
  13. C

    johnson power shift II - to a electroshift lower unit (72model 50hp johnson)

    I have this control, with two cables coming out from it, one is throttle & other shifting.. however probaby this is not the correct control box to wire to a outboard with electric shift lower unit (ie. 72 model john 50hp). - Is it all possible is one question... & how? i like to stay away from...
  14. C

    starter solenoid - testing & wiring diagram

    need to know proper way to connect an starter solenoid (froma car, ie, ford solenoid) to johnson 50hp (wiring diagram if possible). & also to test each connection (S, I, from battery, to starter) And how to test the safety or kill switch they call it, that is bolted on the block, one wire...
  15. C

    johnson powershift II control - lost key!!

    I bought this control box but it has no key, it says 14 where the key goes and turns.. I have read some posts, that this is the number required to get a replacement. Does anyone have replacement or know the part number !?
  16. C

    lower unit from 50hp to 85hp johnson?

    85hp is 71 model and 50hp is 70s.. i dont have all the info ..was just curious if anyone knows ..if a lower unit from a 50hp fit a 85hp johnson ..i have both motors here, lower units look the same!!
  17. C

    looking ..suzuki 9.9 hp '80s power head?

    does anyone have a powerhead in any condition for this motor? with flywheel etc..?
  18. C

    merc. 650 // removed flywheel, now how to re-install ?

    motor: merc 650 1975 3 cyc. while dismantling the powerhead, i forgot to mark down the flywheel so I can re-install it easier.. I did take the dist. off, center flywheel nut, and all the bolts around it (prob. was 8 or so little bolts around the center flywheel nut). since the distributor...
  19. C

    merc 650 - melted top piston rings! what could have caused this?

    motor: merc 65 1975 model, 3cyclinder just looking for opinions on what could have caused this? i took the powerhead apart last night, and found out that the top piston rings were melted down, (flush with the piston outer body).. cyclinder walls were not that damaged, a nice light honing...
  20. C

    80s suzuki 9.9 powerhead

    I have in my hands a 9.9 suzuki outboard, in need of powerhead parts. Its hard to find!! I like them to be used, as this is a project for me. Was wondering if I should just scrap the powerhead and forget about assembling it (i had already dismantled it) and replace it with another one...
Top