Search results

  1. W

    Shoot Thru Hull Transducer

    Looking for a shoot thru hull transducer that shows fish targets and bottom structure, I have a Lowrance Elite Ti 7. Want a Lowrance transducer if possible with a range of 83/200 Khz. Any information greatly appreciated.
  2. W

    1998 Johnson 150 hp FICHT water pump change

    Would like to know how hard it would be to change my water pump. Is thier any thing special that I need to know about removing the bottom out drive, should it be in gear or netural,etc. Any input from you guys would be greatly appreciated. I just purchased the service manual but it dosen't have...
  3. W

    1998 Johnson 150 hp FICHT fuel pump Model# J150ILECR

    Hi everyone, need some help, I think I have a faulty fuel pump. When I turn the key on for the pump to start pumping I only hear power to the pump motor and nothing else, the book says it should pump for 10 seconds and then turn off. I tryied to pump fuel from the fuel tank to the fuel pump and...
  4. W

    Spark Plug Gap

    Wondering what I should set my spark plug gap at. I have a 1998 Johnson 150 hp FICHT engine. I have the pinned heads and are using XC12PEPB spark plugs. I read on the forum that they should be set at .030 but someone said .028 would be a better setting. What do you guys with the knowledge of...
  5. W

    Primer Bulb

    Hi everyone, need a question answered, my primer bulb that I'm replaceing is inside dia. 1/4'', the bulb I bought at the marina was 3/8''. The salesman said that it would work ok, is this true? I have a 1998 150 hp FITCH Johnson fuel-oil injected engine. Any and all answers greatly appreciated.
  6. W

    No Fuel from tank to bulb

    Not for sure if I posted this in the right place. Heres my question, I can not get fuel from the fuel tank to the bulb, the bulb will not suck up any fuel. I have a 1998 1850 Crestliner with a 150 hp Johnson. Any and all answers greatly appreciated.
  7. W

    Correct Position

    Hi everone, I have a 18.2 Crestliner that rests on the side bunks of the trailer and rollers in the center of the trailer. The boat rests on the bunks and the boat is about 2 inches from resting on the rollers. Is this correct. Wish I had a picture to show you. Hope you under stand what I'm...
  8. W

    1998 1850 Tournament Series SC Crestliner

    Hi everone, I posted this on the Crestliner Forum but did not get any responses. Might have a better chance here. My first question is 1. I would like to know what size fuel tank I have. The dealer I bought the boat from says 43 gal. on the paper work, does that sound about right. 2. Where is...
  9. W

    1998 Crestliner Gas Tank

    Hi everyone, been awhile since I've been in iboats forum. Need a couple of questions answered. 1. I have a 1998 Crestliner 1850 Tournament SC, 18'2" lg. I need to know if I have a 43 gal. gas tank. I've had it in dry storage for 2 years with half a tank of fuel. First year in storage I had put...
  10. W

    Pumping fuel out of boat fuel tank

    Hi everyone, been awhile since I've been on the forum. I need some help on how to siphon fuel that has been setting in my boats fuel tank for a year and a half. I put in Sta-Bil about that time also. I tryied to siphon with a 10' hose but can't even get the hose wet. I have a 1998 Crestliner...
  11. W

    Bunk with Rollers

    Hi all, just joined iboats and already have a question. I'm setting up my bunk and roller boat trailer. Question, does the keel rest on the rollers and does the bunks support port and starbard sides. I've asked a few people and I get 3 differant answers. Figured someone from iboats would know...
  12. W

    Mercury 9.9/9.9 Big Foot

    I bought a used 2004 9.9 Mercury. My question is, is the 9.9 same as the Big Foot 9.9, if they are differant than in which way. I have the 15" shaft. Answers greatly appreciated.
  13. W

    Transporting Outboard

    I have a 2003 Mercury 9.9 4 stroke and I would like to know how I should transport it, can I lay it on the side, does it have to stand upright or can I stand it on edge. Thanks
  14. W

    Mercury motor and lower case oil

    Hi everyone, I just purchased a 2003 Mercury 9.9 4 stroke engine, don't have the owners manual so could someone tell me what engine oil and lower case oil to use or recommend. The engine has about 40-50 hrs on it. I ordered the owners manual but will take 2 weeks to receive it.<br />...
  15. W

    3 month old gas Johnson 150 Ficht

    Hi all, would 3 month old gas still be ok to use. I have a 1998 Johnson 150 Ficht engine. Don't want to take a chance, :confused: especially with these engines. Any input would be greatly appreciated.
  16. W

    1998 Johnson 150 hp Ficht Fast Strike

    Hi every one,need a question answered. At idle my engine runs smooth and when running 3000 rpm and above it also runs smooth but between 1500 and 2800 it has a miss like a spark plug is bad. I always clean the plugs every time before I go out and I also index the plugs. Any ideas would be...
  17. W

    1998Johnson 150 Ficht gas filter

    1998Johnson 150 Ficht gas filter Hi every one, just received my parts catalog today and was trying to look up the part number for my fuel filter. Does not show a picture or part number for my filter. I have the canister type which has the water scensor wire. My engine is a 1998 Johnson 150hp...
  18. W

    Thanks

    Thanks WillyBWright for the information. I'm starting to under stand alittle about my engine now with the help from people like you with alot of experience. Thanks again. :)
  19. W

    1998 Johnson 150 Ficht Fast Strike

    Hi every one,new to the board and first time posting. I have a Johnson 150 Ficht Fast Strike,<br />Model# J150U ECR, Serial# 0 04469/08. My question is that I get alot of black soot on the plugs. Installed in the engine is XC12 PEPB plugs. I run about 3500 rpm. After reading some of the posts on...
  20. W

    1998 Johnson 150 Ficht Fast Strike

    Hi every one,new to the board and first time posting. I have a Johnson 150 Ficht Fast Strike,<br />Model# J150U ECR, Serial# 0 04469/08. My question is that I get alot of black soot on the plugs. Installed in the engine is XC12 PEPB plugs. I run about 3500 rpm. After reading some of the posts on...
Top