Search results

  1. No show

    Anywhere to download free OMC repair manual for 1986 Evinrude 90??

    Anywhere to download free OMC repair manual for 1986 Evinrude 90?? the one I have has way too many models in it and not very clear about repair procedures. thanks
  2. No show

    Evinrude 90 trying to get to run right some help Please.. runs real rough and backfi

    86 Evinrude 90 just purchased cheap and I don't wan't to throw good money after bad any help would be greatly appreciated. owner said ran good till it sat. I'm more of a part changer than a mechanic but I do have the manual and did stay at a Howard Johnsons LOL Ok It had no spark on the...
  3. No show

    Electrical 86 evinrude 90 won't start thinking kill switch

    Just got boat . P/o replaced ignition switch it was cranking fine then nothing not even clicks. I looked at faq's could I have actiVated kill switch or something. What is that rubber knob on the controls? I checked the little fuse by the power pack encased in red rubber. I'm trying to do a...
  4. No show

    Just purchased 1986 Evunrude 90 Shes running really rough (SEE VIDEO LINK)

    Just bought it real cheap yesterday hoping it just needs carb cleaning/rebuild . Previous owner said it was running fine a month ago. I cleaned the plugs put fresh fuel 50/1 charged battery shes running irratic up and down sounds like could be a miss. don't remember if you are allowed to post a...
  5. No show

    what is the Proper way to use trim?

    I'm new to I/O and I could not get boat to perform like it should. What is the correct way to to do this ?? I was told to keep alfa drive trimmed in all the way, then when on plane start trimming out drive RPM's will change when lifting till best performance without going too high? Sounds like...
  6. No show

    Need wireing diagram to set up 2 batteries and perko switch

    I'm not too good with diagrams anybody have a simple diagram how I should wire batteries? I have 1 battery now and going to upgrade to 2 batteries and a 3 terminal Perko switch thanks
  7. No show

    Trying to set up two battery system

    I have an 86 Celebrity 210 Cutty.Does anyone have some kind of diagram of how it should be hooked up. I needto go from one batter to two. Thank you:)
  8. No show

    Installation of Alpha One Outdrive Questions about clicking

    86 celebrity 210 cutty just rebuilt the engine and I am installing the out drive. It took a little bit of finessing to get it on. Shifter was in forward all the way to get it on I lifted the gimble mounting plate and shimmed it with a wooden wire brush to lift it higher for me to make it...
  9. No show

    86 Mercruiser 350 Tilt and trim wires 2 wires coming from stern

    I started re doing the motor about a month ago i labeled everything there's 2 wire that come through the back of the hull same length black the label is very worn out looks like it says goes by fuel water seperator but im not sure. can anyone tell me where the 2 wires go ? it looks like a...
  10. No show

    Where can you find Mercruiser free Pdf Repair Manual Link for 86 GM 350

    Where can you find a good link to download Mercruiser free Pdf Repair Manual Link for 86 GM 350 . I bought the Clymer book But it's not to specific I was wondering if There was any thing better. The links from Don S. don't seem to work. Anybody have any good links? Thanks
  11. No show

    Timing and Adjusting Roller Rockers 350 SB 5.7

    Ive installed a 1977 350 small block That was done over with roller rockers. Replacing a 1986 Mercruiser 350 260 HP 5.7 . We did have a flywheel issue which we straightened out. We have two more hurdles to do number one , We are taking everything off the old motor and installing on the 77...
  12. No show

    1986 Mercruiser 350 5.7 260HP 1 pc seal replaced by 1977 2 piece main seal SB 350

    1986 Mercruiser 350 5.7 260HP 1 pc seal replaced by 1977 2 piece main seal SB 350 I am in the middle of an engine swap from a 1986 Mercruiser 5.7 260 HP 350 small block. to replace with an older late 70's chevy 350 small block which has been converted to marine. My friend that is helping said we...
  13. No show

    1986 Mercruiser 350 5.7 260HP 1 pc seal replaced by 1977 2 piece main seal SB 350

    I am in the middle of an engine swap from a 1986 Mercruiser 5.7 260 HP 350 small block. to replace with an older late 70's chevy 350 small block which has been converted to marine. My friend that is helping said we need to get a new flywheel, the problem being the fly wheel on the Mercruiser was...
  14. No show

    Mercruiser 350 5.7 Block Cracked Need to replace

    I am new to this forum or any forum for that matter so forgive me because I am not too sure how to navigate in forums. I will also post picture of crack and above the crack looks like another one on the head but it isn't also I wanted to post a pix of a really cool boat we put in the ocean at...
  15. No show

    Mercruiser 350 5.7 Block Cracked What Now

    I have a 86 Celibrity 210 Cutty with my Mercruiser 350 5.7 has crack in block .just below heads Does anyone know where I can find a not so expensive replacement? What do you think of replacing with a nonMarine engine? Does anyone have a low cost solution to get back to running. I was thinking...
  16. No show

    Need Awnser

    I'm having trouble with tilt and trim if that's what you call it . 1)I belive I have manual tilt (not sure) 2)I is very difficult to lift motor I don't see how you can possibly lift from inside the boat. 3)I guess you lift the 2 tabs they move in conjuction with each other because they are...
Top