Search results

  1. jerkputter

    injectors for my 115 hp 2004 Yamaha engine

    Boat is back in the water and running better than ever before. I got injectors back from Brucato and I was impressed with their work. Replaced all fuel lines with bulb. Installed water separator filter along with the other two. Tank is clean. Cleaned VST. Thanks for all who helped and...
  2. jerkputter

    injectors for my 115 hp 2004 Yamaha engine

    1400 hours. I have drained the tank and cleaned it up like new. No trash now. Now about the water separating filter. There is not one on the engine and not sure where to put one ? Suggestions appreciated. Where would I find one for this 2005 Yamaha engine. F115TLRD ? The fuel lines...
  3. jerkputter

    injectors for my 115 hp 2004 Yamaha engine

    The weather is better in my shop. I have the injectors out and ready for cleaning. I need a seal kit for them. One is cut where it goes into head. Anyone know where I might find a seal kit ? Also all the injectors ohm the same and are good as far as that goes. I am also in the process...
  4. jerkputter

    injectors for my 115 hp 2004 Yamaha engine

    Will do when the weather get warmer. Thanks. I will report back.
  5. jerkputter

    injectors for my 115 hp 2004 Yamaha engine

    I can't find a drain. This is a 50 gallon tank and its in a tight place. I will see what I can do though. Thanks
  6. jerkputter

    injectors for my 115 hp 2004 Yamaha engine

    Will do. Thanks. I will let you know.
  7. jerkputter

    injectors for my 115 hp 2004 Yamaha engine

    Thanks, what if the injectors don't Ohm correct ? do these people that rebuild them check that part? What should the Ohms be on these ? I do agree that this pontoon has fuel issues and I will see if I can find where the problem might be this winter.
  8. jerkputter

    injectors for my 115 hp 2004 Yamaha engine

    I cleaned the VST and had the injectors checked at the same time. A local marine tech sent them off for me but where I don't have a clue. I can't really tell without putting this pontoon in the water and right now the lake is too low to do that. There was no trash in the VST that last...
  9. jerkputter

    injectors for my 115 hp 2004 Yamaha engine

    1200 hours Removed the VST and cleaned last summer and this summer. Ran good for one day or two and back doing the same. Idle is bad and can't seem to get it wide open. Tach don't work but I can tell its not getting full rpm. Boat stored in my shop during winter and at my lake home in summer...
  10. jerkputter

    injectors for my 115 hp 2004 Yamaha engine

    I got a Yamaha F115TLRD engine I need four new injectors. I replaced one a few years ago but now I would like to just buy four new ones now. Any suggestions on where to buy ? The OEM ones look like they would close to a grand if I went that way.
  11. jerkputter

    Tank sending unit

    I have a 2005 Harris FloteBote that I need a tank sending unit for. It has a 50 gal tank . It is 24 inches deep. The type universal sending unit that I bought by mistake will not work because it has the swing arm float arm at top It has to be one with swing arm at bottom of tank, I...
  12. jerkputter

    Winter Storage

    My son bought a new Sea-Doo in July. It has only 19 hours on it now. I was able to put it in my basement for the winter. Before we loaded it I put the correct amount of Seafoam in gas and drove it a few mile. My basement is heated and never goes under 50 degrees. Would there be any use in the...
  13. jerkputter

    Tach goes high after letting off throttle

    My 1999 50 HP Mercury 2 stroke stopped firing on me. I found the stator was defective so replaced it ( 16 amp red ) and regulator and while I had the flywheel off I just bought a new trigger. I don't think this engine has ever ran this good. It idles perfect and starts on 1st try, not like...
  14. jerkputter

    Poontoon boat tank sending unit

    I have a 2005 Harris 24 foot Flotebote that I need a tank sending unit for. I ordered a Moeller universal 4 inch to 28 inch and I cannot get it to work. No matter which I way I turn it the baffles get in the way. The original sending unit had the resistance wire windings at the bottom of sending...
  15. jerkputter

    Water in bottom of cover

    I run my 2000 model 50hp mercury 2 stroke today on my pontoon boat. I was going to check some things being I just installed a new powerhead and noticed water was all in the cowl almost even to bottom coil. I could not find any way to drain this water out. I used the power trim and lifted engine...
  16. jerkputter

    Mercury compression question

    A few months ago I bought a new Mercury 50 hp power head. I have only run it a few hours and it runs ok. Today for the heck of it I decided to check the compression just to see what a new engine has. The engine was not warm. I got only 90 psi but exactly that on all three cylinders. Is that...
  17. jerkputter

    Leaking gas at tank

    I have a 20 foot pontoon 2000 year model with a 50 HP Mercury that now leaks when I prime the bulb around the connection at tank. It is the 5/16 barb fitting with the quick coupler. It has a small o-ring inside the connector that is bad. I think maybe the o-ring could be swelled a little. Was...
  18. jerkputter

    90 hp mercury

    I have a 1999 Mercury 90hp outboard on a pontoon boat. When I parked it last year it was running great. I winterized it and the first time I tried it this season it is having some problems. Runs great at full throttle, idles fine at about 2000 rpms or at 8 mph. When I go at a good cruising...
  19. jerkputter

    Need help on rebuilding carb

    A person brings me a carburetor on an older 9.9 mercury.I think it is a 1990 or earlier. I ordered a kit and bad need a diagram on how everything goes back. It was torn down when I recieved it and I cannot figure the correct way to assemble it back. Thanks for any help. Tom
Top