Search results

  1. O

    Fuel gauge accuracy

    2010 Starcraft 130 Etec 2010. Gauge reads full all week unless boat is flat in the water? Do I need a new gauge or is this normal? I know I am almost empty.
  2. O

    Etec 2010 130

    I have no power to start motor and tilt is dead as well. Everything was fine before I installed a new radio. Radio is fine as is all other functions.I think the problem is in the dash wiring. Fuse or I disconnected something accidently/What should I do to troubleshoot. I need help. Thank you.
  3. O

    Trailer guide posts

    I am having a hard time putting my boat on the trailer am always crooked. My wife is not strong enough to crank the winch. I am in the boat. I am buying trailer guide posts to help but I need advice to know how deep to back the trailer in the water. How deep should I put the trailer in the...
  4. O

    17 foot starcraft with 130 etec

    I am trading my pickup in on either a gmc Yukon or acadia. I am leaning towards the acadia but will it be adequate to pull my boat? I am concerned with safety and stability. Thank you.
  5. O

    Minkota ipilot

    I have a 2010 StarCraft 17 foot with 139 ETEC and mounted on the front a Minkota ipilot. There are 2 12 volt batteries in series to power the ipilot. I want to know how long the electric motor will run before the batteries discharge. I was out on sunday and after 3 hours the batteries had almost...
  6. O

    E tec 130 temperature alarm

    I just bought an E Tec 130 , 2010 and had it out yesterday. The water temperature alarm came on two times. There is water coming out of the back . I shut the motor down waited 5 minutes and stated off again. The best rpm I could get out of the motor was 4800. Looking at the manual it says it...
  7. O

    Lorrance x135

    Not working properly. Worth fixing or should I buy a new one. If I buy a new one will the transducer and power be able to connect? Thank you
  8. O

    Lorance x135

    It defaults to 61 ft. Not working. Should I try to get it repaired or buy a new one? If I buy a new one will the transducer and power cord be compatible? Thank you.
  9. O

    live well flooding

    Starcraft super fisherman 17. I have 2 live wells and the back one fills with water. I did not have a plug in until it filled. Is this normal? I want to keep it dry.
  10. O

    E Tec 130 2010

    I just bought a 2010 starcraft boat with an E Tec 130 2010 model. Are there any known problems or concerns with this motor I should be aware of as far as maintenance and service. All advice and suggestions are welcome. Thank you
  11. O

    E tec or mercury

    I am buying a new boat and have a choice of Etec or Mercury 60 hp. Cost is the same. Which should I choose? Boat 16 foot crest liner.
  12. O

    Tiller motor

    What would be a better motor for 16 ft aluminum tiller? Mercury Yami E tec Suzuki. I was thinking 40 to 60 hp.
  13. O

    Tower of power 1986 115

    Check ignition switch problems. Checked all wires for continuity ok starter ok. Solenoid ok. Suspect ignition switch. Is this a common problem?
  14. O

    1986 Merc 115

    You guys have been a great help with my motor problems. The motor run great once started and warm. It is still hard to start. As per your instructions i squeese the ball until hard. Give it some throttle in neutral. Now here is where i am confused. Am i choking it when i push the key in and hold...
  15. O

    Pulling a tube

    I was out last weekend pulling a tube with my grandkids. 115 mer 2 stroke. Starting out I had to hit the gas pretty hard to avoid the tube going under. Once under way it pulled fine. I had a harness attached to transom clips, low on the boat. Maybe that was the problem. Anyways I did see some...
  16. O

    1986 merc.115 tower of power staring problem

    Just had new carbs rebuilt and I am having problems starting the motor. When I pump the ball it does not get hard. I can hear gas in the bulb but I was told to pump the ball until hard, the put the key in the ignition and push in to choke it. I did manange to get it going and it seems to run...
  17. O

    What product to use fill holes

    I have a 1988 Campion Fishing machine and I recently took the teak off and refinished it. Now I am putting the teak back on. I want to fill the holes in the fiberglass so when I put the teak back on the screws will grab. What product should I use. Thank you.
  18. O

    Hole filling in fiberglass Campion

    I have removed and refinished the teak on a 1988 Campion and the teak turned out great. I want to put the teak back and am wondering what product to use to fill the old holes before I put the new screws through the teak and into the fiberglass. I want the screws to fasten in solid as I am...
  19. O

    merc 115 1986 cowling

    Just wondering if you can buy the replacement cowling for 1986 Merc 115 ? The paint is chipped and the decals on the front are gone. I want to improve the appearance of the motor. Thank you.
  20. O

    Decal removal, oxidation removal and polishing

    Last fall I purchased a 1988 Campion fishing machine. I want to remove the old decals, oxidation and polish the exterior. Can I buy new decals and where would I find them? Also what products and procedures should I use to remove oxidation and polish the hull? Thank you.
Top