Search results

  1. C

    2006 Tohatsu 4 HP No Reverse

    It seems like the clutch push rod is too short. This makes me wonder if I have the spring retainer on the wrong side of the spring pin. Can you confirm that the spring retainer goes on the spring side of the spring pin? Or does is actually go in with the clutch push rod after the spring pin is...
  2. C

    2006 Tohatsu 4 HP No Reverse

    When it is at bottom of bore there is shaft play on the gear (it slides about an 1/8" which appeared to be why I did not have reverse? I will disassemble again today... not sure what is going on here. Thank you for the time
  3. C

    2006 Tohatsu 4 HP No Reverse

    Hi Paul, That is correct, MFS4A2. I looked at a parts diagram and just confirmed that all parts have been installed including the spring holder you referenced. When I just pulled the prop shaft out just now, the cam on the push rod is pointed the correct way as well. It did seem that I...
  4. C

    2006 Tohatsu 4 HP No Reverse

    Good Afternoon, I have a 2006 Tohatsu 4 hp 4 stroke. I had to replace the 3 lower unit gears, bearings and seals after the prop hit a rock. I just wrapped up the rebuild but now I have a new problem. I have no reverse. I disconnected the shift linkage from the selector lever on the motor at...
  5. C

    Yamaha F250 crankshaft

    I don't really care what the crank measures. The bearings are on order from yamaha based on the crank #'s (they offer 3 different sizes) I will install and plastigage them to make sure they will work with the crank. It is a low hours motor with no visible wear on any bearing surfaces. Despite...
  6. C

    Yamaha F250 crankshaft

    Will do, planning to clean everything with compressed air, and dawn dish soap/water. Not in that order...
  7. C

    Yamaha F250 crankshaft

    I used 800 grit paper and wd40. Cut the paper and wrapped each journal and used a shoe lace to pull it around. Came out like new.
  8. C

    Yamaha F250 crankshaft

    I've got a 2006 Yamaha F250 that I am rebuilding. The crank has staining on the journals as seen in the photo. Any issues with this? Should I polish the journals or leave one? It is smooth to the touch with no pitting.
  9. C

    Swim Platform Construction

    Hi everyone. I have a 1984 Carver Mariner 28 that had a 20" wide swim platform on the transom. The platform was soft, the core was rotten, and it was not large enough for our uses (dinghy storage and general boarding). Here is a photo of where I started: Here is a sketch of the supports I...
  10. C

    Running rough, starter working hard

    2000 Volvo Penta 5.7L GS I pulled the motor this past winter and replaced the starter, spark plugs, manifolds, risers, and drive coupler. I just got the engine back in the boat this week and I have the following problems: Starting the engine is difficult. By that I mean the starter struggles...
  11. C

    Changing Drive Coupler As A Maintenance Item?

    I have a 2000 Volvo Penta 5.7L engine mated to a DP-SM drive. The package has 700 hours on it, and I currently have the engine out (painted it, cleaned bilge, etc) and I was wondering if I should replace the Drive Coupler as a maintenance item? I have no issues with it at the moment. Thanks for...
  12. C

    2000 Volvo Penta 5.7L GS - Water In Cylinders

    I have a 2000 Volvo Penta 5.7L GS with 750 hours on it. It is RWC and has been used in both salt and fresh water. I replaced the manifolds 3 years ago with Barr, and the risers 4 years ago with OEM volvo. In early July I started to experience rough running condition at idle speed (misfiring)...
  13. C

    2000 Volvo Penta 5.7 GS Power Steering Pump

    I need to replace the power steering pump on my 2000 Volvo Penta 5.7L GS due to a leak at the reservoir, and I was wondering if I can just go to an automotive store and buy an automotive equivalent (GMC Truck with a 5.7L for example)? Thanks for the help!
  14. C

    Service Life Of Parts - 2000 VP 5.7 GS

    On a 10 year old boat what parts should be replaced for preventative maintenance? I don't mean service items like impellers, cap/rotor, belts, etc that have a set life or recommended change out schedule. What about the items that are never talked about? -Fuel pump? -Ignition Coil? -Relays...
  15. C

    How long for winterizing?

    For those of you with larger cuddy cabin style I/O boats (with water systems, marine head, washdown pumps, ect) how long does it take you to winterize at the end of the season? Here is my list: -change engine oil & filter -fog engine -drain RWC and add RV antifreeze -clean out bilge -remove...
  16. C

    Volvo Penta 5.7L GS - taking a long trip and need advice

    I am preparing to take a 300 mile trip on my 2000 Larson 254 Cabrio with a 5.7L Volvo Penta GS engine, which has 700 hours on it. I plan to replace the following for preventative measures: -Distributor cap and rotor -Spark plugs -Inspect plug wires (2 seasons old) and replace if needed...
  17. C

    Bad Riser gaskets?

    Engine is a 2000 Volvo Penta GS 5.7L RWC. I replaced the manifolds and risers last season with OEM risers, Barr manifolds. Came down to the boat this morning and went to start the engine and just got a solid clunk. I pulled the spark plugs and water came out of half of them (rear half). I...
  18. C

    Does anyone make 10' Aluminum Boats anymore?

    I currently have an 8' row boat as a tender and need something a bit larger, it seems that a 10' aluminum boat would fit the bill but I cannot find any. I do not want a jon boat but instead a V hull with reasonable gunnel height. If anyone knows a brand I would appreciate it! Thanks.
  19. C

    Tach issues on a 2000 Volvo Penta

    I have a 2000 Volvo Penta 5.7L GS engine, and the tachometer is erratic when I operate items such as the outdrive tilt/trim. If I drive a long distance at idle it often will read 3K RPMS when it should be around 1K. If I bump the engine speed up a bit the tach drops down and reads correctly. Is...
  20. C

    RWC Volvo Penta 5.7L GS Temp

    What should this engine (2000 Volvo Penta 5.7L GS) RWC run at for a temp? I installed a 160 degree t-stat and I only see 130 degrees on the gauge, is this normal or do I need to get an IR gun out? Before the original t-stat failed it would run at 175 degrees.
Top