Search results

  1. N

    2005 Yamaha 225 Power tilt Trim Troubleshoot

    Pressure tested and no leaks. Just need trim motor oil changed/filled. All good now. Thank you.
  2. N

    2005 Yamaha 225 Power tilt Trim Troubleshoot

    Replace all the seals?
  3. N

    2005 Yamaha 225 Power tilt Trim Troubleshoot

    Replace all the seals?
  4. N

    2005 Yamaha 225 Power tilt Trim Troubleshoot

    Will not trim up or down when button is pressed. Makes noise when button is pressed. Sounds like motor is still working. One of the ram was stuck but now freed. Oil is milky color. Please assist.
  5. N

    2005 Yamaha F225 TXRD Low Pressure Fuel Pump Replacement

    NVM. Got it. Thanks.
  6. N

    2005 Yamaha F225 TXRD Low Pressure Fuel Pump Replacement

    Can't seem to get it to fit around the LP fuel pump. Thank you ahead for any advise.
  7. N

    2005 Yamaha F225 TXRD Low Pressure Fuel Pump Replacement

    Don"t know where this piece goes to after replacing the LP fuel pump outside of the VST.
  8. N

    2005 Yamaha F225 TXRD rubber grommet replacement

    Thank you. Will try to look for the relay.
  9. N

    2005 Yamaha F225 TXRD rubber grommet replacement

    What do you think about cutting the new grommet to run the wires through and marine caulk after?
  10. N

    2005 Yamaha F225 TXRD rubber grommet replacement

    LOL. LOL. Ok thank you. That way seems to be the safest way.
  11. N

    2005 Yamaha F225 TXRD rubber grommet replacement

    I was planning on cutting them and use butt splice connectors. Then heat shrink. What do you think?
  12. N

    2005 Yamaha F225 TXRD rubber grommet replacement

    I know where to disconect the other wires accept for the blue & green trim wires. I don't think I can disconnect at the trim motor. Maybe at the relay? But don't know where that is located at.
  13. N

    2005 Yamaha F225 TXRD rubber grommet replacement

    Thank you for the reply. Just the grommet.
  14. N

    2005 Yamaha F225 TXRD rubber grommet replacement

    Where do I disconnect the trim wires to feed them through the rubber grommet?
  15. N

    Garmin Striker Plus 7SV Transducer Disconnected Error

    So I shouldn't connect the wires according to the chart? I was going to connect the wires according to their color codes. I was going to connect the blue, black, and shield wires according to their colors on the unit.
  16. N

    Garmin Striker Plus 7SV Transducer Disconnected Error

  17. N

    Garmin Striker Plus 7SV Transducer Disconnected Error

    I am tryin to hook up the Airmar External Transom Temperature Sensor T80 10k ohm Analog Thermister as a fix but do not know how to wire it. There are 3 wires on the temp sensor. They are blue, black, and metallic. What wires on the unit do you connect these to? A wiring diagram will be very...
  18. N

    1992 Mercruiser 4.3 w/ balance shaft and 1 piece rear main seal swap to newer year Vortec.

    Would it be okay to use a vortec block and switch over the cam and the crank from the non vortec?
  19. N

    1992 Mercruiser 4.3 w/ balance shaft and 1 piece rear main seal swap to newer year Vortec.

    Can I use the Automotive vortec heads or do they have to be Marine? What's the difference?
  20. N

    1992 Mercruiser 4.3 w/ balance shaft and 1 piece rear main seal swap to newer year Vortec.

    Will I still be able to use my current 14 1/2 x 15 SS 4 blades prop once the motor is converted to Vortec?
Top