Search results

  1. G

    2009 Yamaha 25 ticking in neutral

    I mean I can go clockwise turning the barrel nut down as far as it will go or turn it counterclockwise till it nearly separates the two shift rods and it has no bearing on the prop from not ticking and slowly turning when in nneutral unless I slightly push the gear shift handle backward towards...
  2. G

    2009 Yamaha 25 ticking in neutral

    Thanks for the suggestion, but the jam nut is on the linkage just below the barrel nut. As I stated earlier , I have adjusted the barrel nut from all the was up to all the way down and the ticking happens everywhere in the range. I have to barely push the shift lever back about 1/4 inch and it...
  3. G

    2009 Yamaha 25 ticking in neutral

    I have not had the lower unit off or the two shift rods separated. I bought the motor used and just noticed the shift ticking after I bought it. Maybe the previous owner had replaced the impellor coz it pees a good stream. I will try adjusting again and make sure it is fully in reverse when I...
  4. G

    2009 Yamaha 25 ticking in neutral

    I bought a 2009 Yamaha 25 hp 2 stroke long shaft tiller steer. It runs great but when in neutral, I can hear a ticking noise from the prop area and the prop continues to slowly turn. I can push back just a little and the noise and the prop stop. When I let pressure off the shift handle, both...
  5. G

    Motor swap- wiring questions

    Thanks, No tilt and trim and no temp gauge- so I don"t have to worry about those !!!
  6. G

    Motor swap- wiring questions

    I guess my triangle shaped plug with all the brown wires is all for trim and tilt-which the motor I am installing does not have. But, yes it is informative info. Thanks for sharing it.
  7. G

    Motor swap- wiring questions

    OK, so basically this guy is using new plug connectors, but a plain old spade connector would do the same thing if you put one on each wire and matched the colors. Unless I am missing something. Thanks for the video.
  8. G

    Motor swap- wiring questions

    I am trying to put a 1989 Evinrude 25 HP, remote steer, electric start on a boat that had a 1997 Evinrude 40 hp on it. The remote shift/ignition box and wiring harness and steering cables were left on the boat. I have the "big red plug " from the 25 HP- both ends - and the wiring cable that ran...
  9. G

    1989 Evinrude 25 hp wiring help

    Actually I said it wrong the "I" is Actually the "A" and the other one is a "B" 2 "M" and one "C"
  10. G

    1989 Evinrude 25 hp wiring help

    Yes, I cleaned off the back of the switch and got my young eyed wife to look.. 2 "M" terminals, one 'C" in the middle, one "I" and 1 "A".. Thx for all your help !! Eye Dr appointment has been Scheduled
  11. G

    1989 Evinrude 25 hp wiring help

    Thank you --- very helpful information !!
  12. G

    1989 Evinrude 25 hp wiring help

    Crosbyman. Can you draw on the picture of my switch which letters coordinate with the terminals? I havew looked at this switch with a magnifying glass and only see 2 "M" and one "I" Thx for your help
  13. G

    1989 Evinrude 25 hp wiring help

    All letters say "M" or "I" only 3 three letters are stamped. There are 6 terminals There are 2 "M's" n one "i"
  14. G

    1989 Evinrude 25 hp wiring help

    Well. on closer examination my switch does not look like the one in the diagram. I am attaching a picture of the back of my key switch so hopefully someone can identify which terminal is for which wire and let me know. There are no markings on the terminals.
  15. G

    1989 Evinrude 25 hp wiring help

    Thanks, this will help a lot !!
  16. G

    1989 Evinrude 25 hp wiring help

    I bought a 1989 Evinrude with remote start that was set up for stick steering and remote key start. All the wires were disconnected from the back of the key so the wiring harness could be removed. There are screw terminals on the back of the key but none are numbered. I cannot figure out which...
  17. G

    25 HP evinrude Etech issue

    Thank you !!!
  18. G

    25 HP evinrude Etech issue

    So the pump in the Amazon link will work on this motor? If so, Great !! I have had the thing apart twice and I can replace it and save $275. Please verify that this is the correct one and I will order it !!
  19. G

    25 HP evinrude Etech issue

    I guess I don't understand the configuration of the fuel system. Is the "fuel pump" housed within the VSP and if so is it replaceable? Is that different than the " Fuel lift pump" ? Where is the fuel lift pump located? Is it behind the oil tank, coz I don't see anything that looks like a...
  20. G

    25 HP evinrude Etech issue

    I checked the fuel pressure at the valve on the inlet and I am getting zero psi. Where else do you check ? I dont see any other valves to put the tester on.
Top