Search results

  1. AMMO DAWG

    Looking to Upgrade My Graphics

    It's spring and pulling the 2006 Sea Ray out of a winter sleep and realize the graphics are really worn and tired. There's no hope to get the original so looking for some ideas on some graphics you all may have put on your bow riders. The picture is pretty old, just wanted to show the color...
  2. AMMO DAWG

    Water in Oil (Again) Head Scratcher

    The thought has crossed my mind, I'll let all know how it turns out!
  3. AMMO DAWG

    Water in Oil (Again) Head Scratcher

    I did a pressure test on the manifold and acetone on the riser, not leaks found ( check previous photos)
  4. AMMO DAWG

    Water in Oil (Again) Head Scratcher

    No. I do not have a cover, I bought the coat used and it didn't have one. I'll be on the lookout for one to add, thanks.
  5. AMMO DAWG

    Water in Oil (Again) Head Scratcher

    Update 3 - I did a check of the Manifold and Riser mating surface with a .002 feeler gauge and couldn't slip it under my straight edge. Can't find a smoking gun, starting to think somehow rain got in from the top which doesn't make sense either unless if got through the breather somehow...
  6. AMMO DAWG

    Water in Oil (Again) Head Scratcher

    Update 2 - Rigged up a plate to go over the thermostat housing and plugged the water pump hose with a piece of PVC with an end cap and hose clamp. In the first picture I was being lazy and used some scrap aluminum plate I had as is. Had a slow leak and realized it was my plate leaking. Went...
  7. AMMO DAWG

    Water in Oil (Again) Head Scratcher

    Update - Weather has been crap and work keeps getting in the way but I'm back on the investigation. Thought I would start with the manifolds and risers and hopefully eliminate them as the issue since they are virtually brand new. I rigged up a manifold and a blocker plate and pressurized both...
  8. AMMO DAWG

    Water in Oil (Again) Head Scratcher

    Ok, I plan to fab a plate to fit over each exhaust side of the heads to block the water passages, pull the thermostat housing and make plate with a air fitting and gauge and plug the hose from the water pump. 15-20PSI. Is hat a good plan, how long should it hold pressure is its good. I'll...
  9. AMMO DAWG

    Water in Oil (Again) Head Scratcher

    I'm using Mercury Service Manual Number 25, intake is 11 lb-ft for GM V-6 (4.3L)
  10. AMMO DAWG

    Water in Oil (Again) Head Scratcher

    It's a Vortex, looked through the parts manual and owners manual and there is little to no reference to the engine other than general safety stuff.
  11. AMMO DAWG

    Water in Oil (Again) Head Scratcher

    Thanks all, I haven't had it in the water yet, unfortunately been busy pulling and installing the engine and never got it out to the bayou. Since I haven't had it in the water with the 4.3 not sure where the water line is. Is there any harm putting a spacer in even if it takes it above 14"? I...
  12. AMMO DAWG

    Water in Oil (Again) Head Scratcher

    I have a 2006 Sea Ray 185 Sport that I have been repowering from a 3.0 to a 4.3 and have an issue I just can't seem to resolve. Awhile back I found a donor 4.3 and outdrive and had the engine rebuilt at a machine shop I have used in the past. I purchased a set of aftermarket exhaust manifolds...
  13. AMMO DAWG

    thunderbolt iv sensor

    Let me know if I can help with that Delco if you go that route, fairly straight forward install, thanks
  14. AMMO DAWG

    4.3 Engine coupler issue?

    This is the one I use, a bit pricey
  15. AMMO DAWG

    4.3 Engine coupler issue?

    Thanks Rick, just needed that little nudge!
  16. AMMO DAWG

    4.3 Engine coupler issue?

    Thanks all, I'll be sure to update with a happy ending hopefully if this rain ever gives us a break!
  17. AMMO DAWG

    4.3 Engine coupler issue?

    After scouring the old inter-web for a new coupler come to find out OEM couplers are very pricey and the next best (in my opinion) the Sierra are sold out anywhere that has them for a decent price. There's lots of Chinese aftermarket couplers out there, but I'm not going to do that again. So...
  18. AMMO DAWG

    New to boats and about to burn down my boat. Need some help with wiring.

    I had an intermittent ignition on my 4.3, it had the Thunderbolt ignition, regardless I understand the frustration. Some on this forum might not agree, but I went to a Delco ignition system for marine use and man what a difference. Went from cranking to instantly firing up, not to mention a...
  19. AMMO DAWG

    4.3 Engine coupler issue?

    Thanks Tank! Pretty sure the transom is good, and not sure if it's an approved method but I put a few drops of two part epoxy to hold the leather washer in place cause you're right, no space at all. While trying to dodge rain I did some more low tech testing, I put the new coupler on with a 1"...
  20. AMMO DAWG

    4.3 Engine coupler issue?

    Thanks, it is the same engine, took it back to the machine shop that built it and they did a pressure test and leak down test, turns out it had a bad head gasket, no cracked block or head glad to report. I have run it quite on bit on the ground and oil is good. I see your point on the quick...
Top