Search results

  1. K

    Engine id, came across this , thought i would share

    Hello Interesting info had not seen before. Click on the picture , then click again and should open big enough to see, you can then right click the picture ands either save it to you computer or print it. Happy hunting :-)
  2. K

    Installing fuel/water seperator questions

    Hello I am installing a fuel/water separator filter, some questions 1. does the squeeze bulb go before or after the filter 2. does the filter need to be mounted below the output from the tank. 3. do I need to "prime" the filter ( fill it with fuel ) thank you
  3. K

    92 johnson 140 hp vro pump

    Re: 92 johnson 140 hp vro pump Hello Before spending a ton of money do the following Go to Oriely's or auto zone and borrow their radiator cap test kit, remove the cap adapter from the pump and hose and get a 1/4 to 3/8 adapter and some 3/8 hose to allow hookup to the puls hose adapter on...
  4. K

    Testing VRO Pump.

    Re: Testing VRO Pump. Hello Go to Oriely's or auto zone and borrow their radiator cap test kit, remove the cap adapter from the pump and hose and get a 1/4 to 3/8 adapter and some 3/8 hose to allow hookup to the puls hose adapter on the pump follow attached troubleshooting procedure.
  5. K

    Decarbing, can i let the mixture soak overnight ..or not

    Hello I am decarbing motor according to Capt. Bob Dunkelburger decarb FAQ I have done the Decarb acording to the instruction however am running out of time to run the beast in my neighborhood, can i leave the mixture overnite or do i need to run CLEAN fuel through it tonight? 1993 Evinrude...
  6. K

    Squeeze bulb question

    Hello on my old 70 hp stinger the squeeze bulb will pump up hard BUT on my new ve175gletr 175 hp 1993 evinrude intruder the bulb will not get hard new bulb and line, no leaks , VRO Disabled ( but still VRO fuel pump) when i squeeze it i get this sound like a frog coming from the top left side...
  7. K

    power coil readings to high

    Hello 1993 evinrude 175 glet power coil reading for voltage and ohms to high dva voltage connected 49 should be 11to 22 dva voltage disconnected 190 should be 45 to 120 resistance 90 ohms should be 50 to 60 This is the black sleeved stator and blue sleeved power pack my understanding is...
  8. K

    Tach pole settings V6 evinrude

    Hello I have a 1993 175 hp evinrude intruder ve175gletr What should the tach pole setings be .. 6? thank you miker
  9. K

    How to remove the optical timing encoder wheel withou destroying it ?

    Hello All Does anyone have any tips for removing the plastic optical encoder wheel from the crank shaft without destroying it, i have to replace my optical sensor, or should i just order a new one while i am at it. 1993 evenrude intruder 175 hp thanks miker
  10. K

    1993 evinrude intruder optical sensor loose

    Hello the tabs on the optical sensor are actually broken and it is just sitting there wiggle wiggle Question : was having a problem with the motor dying a 1/2 to WOT, just like you turned off the switch at slow speed engine USSUALY ran ok but would turn off sometimes Could this be the...
  11. K

    1993 evinrude intruder question

    Hello I have a 1993 evinrude intruder 175 hp model e175glet has 110 compression in all cylynders but 1 which is 100 I have not / and probably never has been de-carbed motor runs good / has CDI problem (ordered DVA to trouble shoot) may need new powerpack is this enough compression to make...
  12. K

    1993 Evinrude Intruder system check gauge ?

    Hello I have a 1993 evinrude intruder 175 hp model e175glet is there a system check gauge i can install in the dash ? part # ? Thanks miker
  13. K

    1993 Evinrude Intruder how to instal Temperature Gauge ?

    Hello I have a 1993 Evinrude Intruder 175 HP model e175glet Can you install a temperature gauge on the motor I think it may be running hot and causing the motor to die thanks miker
  14. K

    1993 Evinrude intruder keeps dying at speed

    Hello All I have a Evinrude Intruder 175 hp # VE175GLETR (VRO REMOVED before I bought the boat) Just bought the boat. (1994 Bayliner Redevous 2609) The engine has had this problem for awhile. Boat starts and idles fine, runs slow fine, but when you run it 3/4 to WOT it will run out good the...
Top