Search results

  1. J

    blackmax 200hp 1989 problems

    Hi Guys thanks for both your help. Hopefully you see this message. Its been about 7months since working on the motor. My memory is hasie and I think i may have documented a video Of the last problem on had on the engine. (Well I hope I did a video)that will help me. Okay so what I can remember...
  2. J

    blackmax 200hp 1989 problems

    , two blue ,two red, two yellow and one black
  3. J

    blackmax 200hp 1989 problems

    Just wondering is there supposed to be continuity between the black ground to red/white? their also continuity from black to single red on the stator
  4. J

    blackmax 200hp 1989 problems

    cheers
  5. J

    blackmax 200hp 1989 problems

    Thanks Good idea
  6. J

    blackmax 200hp 1989 problems

    does that involve all the wires including the wires that go to the coils?
  7. J

    blackmax 200hp 1989 problems

    I did some more testing, dva tested trigger, stator ,coils and packs. All tested good apart from trigger low voltage 2.2v.I then removed idle/stabilizer wires and voltage came back up to spec on trigger. I also did this test(not in the merc manual I have). Hopefully I worded it correct. I...
  8. J

    blackmax 200hp 1989 problems

    I get confused easy haha. Ill send a video link hopefully tomorrow .
  9. J

    blackmax 200hp 1989 problems

    okay slowly learning the regulator and rectifier are two different things yeah? I just haven't read about them yet in the book I have. My workshop manual in some parts bit hard to understand its fallen to bits.Is the idle stabilizer on top or on the port side? There's two black boxes that look...
  10. J

    blackmax 200hp 1989 problems

    Thanks for the reply 16amp Oh and its a 1989 model
  11. J

    blackmax 200hp 1989 problems

    Hi, I am having problems with my mercury 200HP.1989 not 1998 I redid the carbys 2 years ago. The engine has been sitting. I took it out a few weeks ago. I put in fresh fuel and some sea foam. I ran it on the muffs a few times during the week before heading out. Most of the carbon was gone. Not...
  12. J

    200hp outboard mercury blackmax swivel arm bracket engine is around 1986model and sea star steering.

    Thanks for the reply. Washer goes on top of bottom yoke will I have to take power head of ?
  13. J

    200hp outboard mercury blackmax swivel arm bracket engine is around 1986model and sea star steering.

    I replaced my old swivel arm bracket about 18months ago.Iv finally got around to putting lower unit back on.Looking in my box of parts I noticed a wave washer.Looking at swivel arm bracket looks like I did not put it in. Would this cause problems if I was to leave it of? And if i do put the...
  14. J

    filling holes then re drilling in bottom of fiberglass ski boat to fit Finn

    Looks to be fiber glass, ply then gelcoat.
  15. J

    filling holes then re drilling in bottom of fiberglass ski boat to fit Finn

    Holes are bigger then what I said probably 6-7mm bigger. Here is a link to videos Thanks for your time.
  16. J

    filling holes then re drilling in bottom of fiberglass ski boat to fit Finn

  17. J

    filling holes then re drilling in bottom of fiberglass ski boat to fit Finn

    Hi thanks for the reply,could i put a link in here to you tube and share a video?
  18. J

    filling holes then re drilling in bottom of fiberglass ski boat to fit Finn

    HI To start with please excuse my spelling its been a long day and its late here. Needing some advice.I am fitting two finns to the hull the hull is around 18mm thick.Looks to be made of wood fiberglass and gelcoat. I have access to both sides.There are bolt holes in place from the ski pole so...
  19. J

    Mariner 175hp serial number ,parts,

    Hi Im new to this site so i hope i have the right place to post this. I have a mariner 175hp I would like to know what year the motor was made.I cant find the serial number on this site.Im sure it would be here but since im new ill need your help. SERIAL NUMBER IS OC221001 Would parts for...
Top