Search results

  1. S

    Help removing broken screw

    Hi guys, any advice on how to remove 2 broken screws..I will really appriciated any advice... Thank you
  2. S

    1991 evinrude 175hp help????

    Hi guys, on a 1991 175hp Evinrude, Do you guys know, if I install the Impeller housing with only 3 screws, do you know if it holds, the reason I?m asking is one of the screws broke, and when trying to remove the broken screw, the Lower unit housing got damage where the screw goes in, I don?t...
  3. S

    1991 evinrude 175hp Lower unit stock

    Hi guys, Evinrude 1991 175hp , I have remove every bolt, shift rod is also loose, I can?t get the lower unit out, I think shaft is seize on crank shaft, here is what I did, I have the Motor upside down on a engine hoist, I try to get the lower unit loose that way, did not work, J have cut a...
  4. S

    Evinrude 1991 175hp Trim ????

    Hi everyone, I have an Evinrude 1991 175hp, model number: VE175TXEID, my trim motor just gave-up, it will only go up if I hit it with a hammer, my questions is any idea what is the part number on that trim motor? I look allover and I have no clue. I will appreciated any help Thank you
  5. S

    Evinrude 35 hp Electric start

    Hi guys, on a Evinrude 35 hp Electric start, Motor was with steering system and remote control, I did convert to a tiller outboard but I?m trying to install a omc Push to choke key switch on lower pan, Do you guys know witch wire( color) on the harness( above picture) is to trigger the...
  6. S

    1991 175 hp temperature ??????

    Hi guys, I have an Evinrude 1991 175hp, model number: VE175TXEID, I'm try to figure it out, if the temperature gauge is working properly, any idea what is the temperature that this motor should be running at? The reason that I?m asking is because the motor on ear muff since like it is getting...
  7. S

    1991 175hp Max RPM ??

    I have a 1991 175hp Evinrude with 35amp charging system, any idea what is the max rpm? And at idle is 900 rpm ok? I?ll appreciated any help Thank you
  8. S

    1996 Mercury 5 hp won't start

    Hi, I have a 1996 Mercury, 5 hp one cylinder, compression is 90 Psi, spark is good and fuel on carburetor, but motor won't start, after priming the carburetor, on the second pull it will make one loud explosion and that's about it after that you can pull all you want and nothing happens, it...
  9. S

    1991 Evinrude 175hp Carb ?????

    Hi, I have a 1991 Evinrude 175hp, 35 amp systems, electric primer system, Motor only start in manual mode, if I turn the red lever on the electric primer down, the carbs will get fuel and the motor will start right up, once I move the red lever to the original position the motor will shut-off...
  10. S

    1991 evinrude emergency cutt-off switch

    Hi, I order a cut-off switch for my 1991 Evinrude 175 hp, 35 amps, the omc manual only show 2 wires yellow-black and black, but the cut-off switch came with 3 wires, Yellow-black , black and black. Any idea where the other black wire goes to. I connected the yellow-black wire to the M...
  11. S

    Vintage Johnson ??

    Hi, any idea if I can swap cowl and tiller arm from a Johnson 1961 QD-QDL-22 to a Johnson 1960 QD-QDL-21? I appreciated any help Thank you
  12. S

    1961 evinrude 10 hp???

    Hi, are the pinion gears from a 1961 evinrude 10hp, the same as the 1957 evinrude 10hp? Can I swap pinion gears? Thank you
  13. S

    Help with RPM gauge

    RPM gauge is always below 0, If turn the switch without cranking, RPM gauge goes to 0, when I crank the motor RPM goes back below 0, any idea what could be wrong? Is there any way that I can test the RPM cable with a digital meter? Just to see if the motor is sending the RPM. I don?t know if is...
  14. S

    1991 Evinrude 175 hp stator????

    Hi. How bad is it, if I see sparks coming from underneath the flywheel, at Idle it is fine, (no noise, no sparks) but once you hit the throttle, there is a noise like metal grinding and sparks are flying out all over from underneath the flywheel. I will be pulling out the Fly wheel tomorrow...
  15. S

    1991 Evinrude 175 hp lose cable ???>

    Hi, any idea what is this lose cable for? Thank you
  16. S

    1991 Evinrude 175 hp Lower Unit ?????

    Hi, I have 1991 Evinrude 175 hp, Model: VE175TXEID, that I need to replace the Impeller but Lower unit won?t come lose, I got all the bolts remove even the one that is underneath the stabilizer, I also remove shift rod pin from underneath the carburetor, and the Lower unit wont come lose, Is...
  17. S

    1991 Evinrude 175hp?????

    Hi, I have an Evinrude 1991 175hp, there is a water hose lose, any idea where this hose go to? I will appreciated any help Thank you here are some pictures:
  18. S

    Mercury 25 hp Prop Shaft ?????

    Hi, I have a mercury 25 hp, the Propeller shaft is bend, the motor will spin fine but it just has a little bid on bend on the shaft, you can see it by looking at the propeller with the motor running on gear. My question is, is there any way that I can repair the shaft with heat or any other way...
  19. S

    Mercury year & hp ????

    I just got nice mercury, serial: OB221806 , does any one know year and hp. I will really appreciate any help Thank you
  20. S

    Mariner 15 hp ????

    Hi there, I have a Mariner 15 hp, serial number: Oc113818 is there anyway too know what year this mariner is? the Motor has 120 psi on top cylinder and 40 psi on Bottom cylider:'( , I need to buy the repair manual before I do anything to it. I will really appricited any help Thank you
Top