Search results

  1. A

    1980's serial number / harness / general questions

    good day. anyone know what are the specs for the power head bolts serial number for the block is 6033659 and the head number is 95081. I was trying to replace the buzzer alarm sender and snap 2 bolt within OMG... any way if I cant extract them I wont have a choice to remove the power head and...
  2. A

    1980's serial number / harness / general questions

    Quick update nothing Ive done worked. I was able to tap a new hole in the ram and got the power trim system to work for now this will do and get back to this another time thank you all for all the suggestions / help
  3. A

    power trim removal of center cylinder

    Quick update nothing Ive done worked. I was able to tap a new hole in the ram and got the power trim system to work for now this will do and get back to this another time thank you all for all the suggestions / help
  4. A

    power trim removal of center cylinder

    Yes North Coast New Brunswick
  5. A

    power trim removal of center cylinder

    today I try another a way heat tension and gentle taps
  6. A

    1980's serial number / harness / general questions

    hi all. today I try a different way heat and tension and gentle tap on the head bolt
  7. A

    1980's serial number / harness / general questions

    still wont budge
  8. A

    1980's serial number / harness / general questions

    still won't budge...
  9. A

    1980's serial number / harness / general questions

    10 minutes later :) I may have figured it out! Ive been heating up the pivot pin every so often while working on other stuff and adding WD penetrating formula when looking at the part diagram you sent I'm going to take a heavy duty bolt that fits in the center of the pivot pin use the impact...
  10. A

    1980's serial number / harness / general questions

    no worries at all. my issue is 28 is it to be pulled out? screwed out? I used a slide hammer a few shots to see if it would move some nothing
  11. A

    1980's serial number / harness / general questions

    hi. its lifted and well secured but will need more feedback as to how / what tools is required so far all has failed. I've been treating the assembly with WD40 specialist penetrant and no luck thus far will keep doing researche on my end and invite any suggestions. when I look at this assembly...
  12. A

    1980's serial number / harness / general questions

    hi I have the engine up trying to figure out how to remove the single ram to have it repaired one stripped hydraulic fitting at the top and not sure if the ram can be removed without taken the engine off the boat. I started a seperate post for that here are pic of the power trim
  13. A

    power trim removal of center cylinder

    I was thinking about that... and have such a tool :) what the heck will give that a try thank you...
  14. A

    power trim removal of center cylinder

  15. A

    power trim removal of center cylinder

    perhaps the center hole is a reverse tread bolt that is required?
  16. A

    power trim removal of center cylinder

    hi all. I assume I need a puller of sort my concern this is was used as a salt water engine and when I removed those covers to expose the center pin with center threaded hole I'm assuming it's going to seized had slat deposits inside of the cover. will spray penetrate WD-40. I have another post...
  17. A

    1980's serial number / harness / general questions

    good morning sorry for the delay added pic will add more today.
  18. A

    power trim removal of center cylinder

    no problem. thank you
  19. A

    power trim removal of center cylinder

    hi. it's a hard one to figure out have another post open but we think 1982 V6 200 HP
  20. A

    power trim removal of center cylinder

    good day all. could someone explain how to remove single center cylinder for a replacement see pictures. I see the top part will be a pin to knock out its the bottom one not sure how to go about it. thank you all
Top