Search results

  1. C

    Timing, Ground plug boots

    This is what I use to ground the spark tester?
  2. C

    Timing, Ground plug boots

    Leads will be long enough to reach the ground at the starter? Both leads need to be connected to ground or just the clamp?
  3. C

    Timing, Ground plug boots

    Updated attachment
  4. C

    Timing, Ground plug boots

    '03 Mercury XR6 150 CDM Carb engine Can this be used to ground the plug boots so I can time the engine? Its a spark tester but I can set the gap to 0. Worried if my boots will reach. What would be the best spot to hook the leads that come off this tester? Any help you can give me will be much...
  5. C

    '02 Charger boat

    Does anyone know where I can get a Charger steering wheel for an '02?
  6. C

    TPM

    CDI sheet - page 3 Erratic/Advanced Timing: #2. Check DVA on white/black wire. Where is this wire?
  7. C

    TPM

    How do you test the TPM?
  8. C

    Mercury XR6 150

    I can see/know the difference between OEM/CDI. Both sheets list different specs. Both t/s doc is from CDI, so it should be the same across the board not different specs depending on what page you look at.
  9. C

    Mercury XR6 150

    Prop is a Ballistic 3 blade. No other markings found that tells the pitch. Don't believe that is the problem. If I was unable to reach max speed then that would be related to prop pitch/size. Posted two images/sheets. Both have different specs for ohms resistance for stator. Which one is...
  10. C

    TPM

    Timing Protection Module: Part#857185T1 Can anyone explain its purpose/function? Does this have capacitors that store DC? Does this work in conjunction with the trigger?
  11. C

    Mercury XR6 150

    TPM would not be at fault since I have spark on all CDM? Is that correct?
  12. C

    Mercury XR6 150

    Can the ign output be tested for specs OR is that where the CDM test harness comes into play?
  13. C

    Mercury XR6 150

    According to CDI, Trigger specs 1100-1400 ohms / 4+V Trigger: P/B 896 ohms 4.9V W/R 1082 ohms 6.3V B/Y 1155 ohms 6.3V Peek volts check out, just low ohms output. Signal is coming from the trigger. If it's not firing at the TDC, would having a bad trigger cause this issue OR is this more a...
  14. C

    Mercury XR6 150

    Is the Stator/Trigger within specs?
  15. C

    Mercury XR6 150

    idle mixture screws do nothing more than help with idle. They're set 1 1/2 turns out +-1/2.
  16. C

    Mercury XR6 150

    Anyone able to provide any insight to the questions or have experienced this issue?
  17. C

    Mercury XR6 150

    Stator and Trigger - Are they within specs? Can you test the control module input/output? Do I need to get a CDM wire harness to test inline?
  18. C

    Mercury XR6 150

    According to CDI, stator ohms reading on one sheet is 380-430, other sheet 660-710. Which is correct? Stator: 429 ohms 221V Trigger: P/B 896 ohms 4.9V W/R 1082 ohms 6.3V B/Y 1155 ohms 6.3V Good spark able to jump 7/16 gap on all CDMs. Cylinder compression is in the 130's and within 10%...
  19. C

    Merc XR6 service manual

    Anyone know where to get a service manual just for a '03 Merc XR6 150 / ID#1150454AD?
  20. C

    Mercury XR6 150

    02 Mercury XR6 150 carb engine rebuilt carbs - needle/seat/gaskets rebuilt fuel pump / new fuel line new plugs /gapped new water pump /stats / poppet relief valve When I throttle up the boat never planes out. Outboard never dies. Just falls flat. Like it has no power / or lack of. Thought it...
Top