Search results

  1. LIPowersports

    Yamaha Command Link Square Speed Gauge Not Registering Fuel

    My mistake wrong link. This is the gauge that is attatched to a mechanical fuel sending unit. https://rochestersensors.com/wp-content/uploads/DS-923.pdf According to the link, there’s supposed to be a positive 12 volts and ground which all checked out.
  2. LIPowersports

    Yamaha Command Link Square Speed Gauge Not Registering Fuel

    Yamaha Command Link Square Speed Gauge won’t register how many bars of fuel in tank. The boat has two seperate tanks with new mechanical/magnetic senders (click the link) https://www.moellermarine.com/moeller-marine/fuel-accessories/swingarm-mechanical-sending-unit-12-tank-depth-035754-10/ For...
  3. LIPowersports

    LF225XCA Trim Piston Binding

    Yes so when movement transitioned from Tilt to Trim, that’s when the binding began. I probably could have worded it better.
  4. LIPowersports

    LF225XCA Trim Piston Binding

    Took the cylinders back apart and discovered the circlip and o-ring orientation on the trim piston was wrong. Slapped it back together, good as new!
  5. LIPowersports

    Inboard/ I/O Engine Hoist Ideas?

    What are your suggestions?
  6. LIPowersports

    LF225XCA Trim Piston Binding

    2011 LF225XCA left trim piston binds immediately engaging in trim after tilt. The trim piston and seals were changed due to a trim fluid leak. Last season after install, the trim moved smoothly then after a few weeks it started sticking to the point you’d have to toss your weight on the back of...
  7. LIPowersports

    Mercruiser 4.3 Alpha One Stalling Into Neutral

    Those shift assists have really caused problems? Personally I think its a cheesy idea. Maybe Ill have to try it without the shift assist linkage.
  8. LIPowersports

    Mercruiser 4.3 Alpha One Stalling Into Neutral

    Apparently everything has been changed (upper/lower cables, interuptor switch, shifter at helm and the upper Alpha drive portion.) I’ve spent hours playing with adjustments according to Mercruiser’s spec and still no luck. Cables move freely while disconnected. Sometimes the boat stalls shifting...
  9. LIPowersports

    Mercruiser 4.3 Alpha One Stalling Into Neutral

    Typical issue stalling while shifting into neutral. Sometimes the boat almost stalls and other times it does. I checked the cable measurements all seemed fine including cable play amount. While watching the shift interuptor switch and shifting, I noticed the switch isnt always moving as it...
  10. LIPowersports

    Inboard/ I/O Engine Hoist Ideas?

    This one does, my mistake. Could be a great system but it’s sorta limited upon what can fit under it.
  11. LIPowersports

    Inboard/ I/O Engine Hoist Ideas?

    I searched some videos quick of Jen poles… nifty idea. This guy has me thinking.
  12. LIPowersports

    Inboard/ I/O Engine Hoist Ideas?

    I like the idea of gantry’s however they limit your ability by job depending if the boat can fit between it; atleast one like the HF I posted. A forklift is limited too when swim platforms exist. I’m all about investments which is why I’d like to hear about other ideas since there’s so many...
  13. LIPowersports

    Inboard/ I/O Engine Hoist Ideas?

    Hey all. Completed a project over the weekend removing a 454 and changed the engine coupler (pictures below). Normally a skid steer or forklift is used to hoist engines out, I’ve done a bunch, but my resources were limited and I had to get creative. I was wondering if anyone has ideas of a...
  14. LIPowersports

    Bravo 3 Shifting Issue

    I already own a service manual and have briefly glanced at what would be involved however Im curious if anyone could steer me in the right direction to what else I should check on the drive side before complete drive disassembly.
  15. LIPowersports

    Bravo 3 Shifting Issue

    Yes the drive was installed while in neutral and I made sure the latch was locked on the cable before full assembly.
  16. LIPowersports

    Bravo 3 Shifting Issue

    Howdy. Bravo 3 wont shift forward or reverse however prop spins freely both ways like its in neutral. I checked the cables all looked ok. Drive was removed and I couldn’t find FWD manually shifting the fork of course while spinning the shaft. I can find reverse no problem. If I play with the...
Top