Search results

  1. R

    Is 40 lbs pressure enough?

    I read somewhere that when using muffs I should cover same inlet. Thanks for reminding me to do that.
  2. R

    Is 40 lbs pressure enough?

    Update finally found a set of muffs that work with my water pressure and volume. Since these split water to both intake sides and have less leakage I can now run motor on hose.
  3. R

    Voltage between batteries and aluminum hull

    But only when engine cable was removed. Removing any other had no effect.
  4. R

    Voltage between batteries and aluminum hull

    Update spend two days tracing grounds none are grounded to hull. Only way to get o volts between batt. POs and hull is by disconnecting batt neg from motor. So as airshot and cyclops222 say must be the motor grounding to hull. As I said earlier can’t feel any power when touching batt POs and...
  5. R

    Voltage between batteries and aluminum hull

    Kinda of what I thought, but so far have not found a ground to hull. Except for OB which ic grounded and then thru bolted to transom.
  6. R

    Voltage between batteries and aluminum hull

    Was putting cover caps on batt terminals when I discovered there is voltage between batt pos and hull. See pictures. I don’t feel a shock if I touch POs terminal and hull but ohm meter shows batt voltage. Maybe since motor is grounded and is bolted thru hull this could explain. Or do I have a...
  7. R

    12V battery system - adding ACR

    I know this is several months old, but it gave me a lot of good information. Thank you
  8. R

    Is this propped up enough

    Thank you got pin out was only surface rust. Cleaned it up with emery cloth, put light coat of grease on and reinstalled. The propping up worked good barley had to tap pin to remove.
  9. R

    Is this propped up enough

    Thank you.
  10. R

    Is this propped up enough

    Want to pull rusty bottom pin. Do I have motor propped enough? It is a 30 hp nissian.
  11. R

    2 mantiaance questions

    Thanks. I don’t like the rust, pin is still solid but…….
  12. R

    2 mantiaance questions

    Two question on maintenance for a 30 hp outboard Nissan motor. Number one looking ar t the first picture where do I grease this . 2nd question is there a way to remove and clean the rod shown in picture 2? As you can it is rather rusty. Thanks in adavance.
  13. R

    Is 40 lbs pressure enough?

    Thank you. Will use trash can if needed to run while at home.
  14. R

    Is 40 lbs pressure enough?

    When using hose with muffs no water from telltale. When in trash can with water above cav plate water came out of telltale in less then 30 sec.
  15. R

    Is 40 lbs pressure enough?

    Hose is 25 feet no kinks.
  16. R

    Is 40 lbs pressure enough?

    Don’t know flow Tate. No work done to engine other then hookup tach. Drag in my curb side trash bin filled up to 8 inch above cavation plate stared engine in less then 30 seconds water was coming out telltale. So I figure I don’t have enough flow. Thanks for replies. On to the next little thing.
  17. R

    Is 40 lbs pressure enough?

    Started engine for first time in 40 days. Had muffs on turned on water then started motor [started right up] didn’t see water from Pete hole after 30 seconds so shut down motor. I have 40-45 lbs pressure on hose, did I not wait long enough? Motor has been in vertical position whole time. Reason...
  18. R

    Bilge blower question

    Yeah I hear you. It did make a pain putting new filler hose on.
  19. R

    Hydro sheild

    After much reading here and internet I went with doelfin. Liked mouthing better. Waiting on weather to try it out.
  20. R

    Hydro sheild

    Let it out. We want to know.
Top