Search results

  1. M

    Evinrude 9.9 HP Model # 10924B

    There is local shop here in Calgary Automarine. Unfortunately they don't accept any outboard before 2010. There might be solo mechanic on kijiji or facebook but they are charging more than the shop. Might sell this AS IS.
  2. M

    Evinrude 9.9 HP Model # 10924B

    Its get started now without choke but still keep shutting down after few minutes. Upper shaft get hot and white smoke is coming from the exhaust. I still need to pump the bulb while tank is upper than engine to keep it running. Also I don't see any air pulsing feels when put finger on the port...
  3. M

    Evinrude 9.9 HP Model # 10924B

    here is the carb.
  4. M

    Evinrude 9.9 HP Model # 10924B

    I will check. Thanks
  5. M

    Evinrude 9.9 HP Model # 10924B

    I bought new bulb but not the hose.
  6. M

    Evinrude 9.9 HP Model # 10924B

    I don't have marine battery but the car battery. I can just touch +ve and -ve it will start?
  7. M

    Evinrude 9.9 HP Model # 10924B

    Thanks. I did put up above the engine still the same issue. Will try to test engine pulse port next. Spark plugs are little black when I pulled them out.
  8. M

    Evinrude 9.9 HP Model # 10924B

    Blow test pass. Everything looks so clean in and out. Don't know what to do. I did pump 4 times. Only start in choke fully out. But shut down right after even choke is pulled. Not even start without choke pulled out.
  9. M

    Evinrude 9.9 HP Model # 10924B

    I did the pump done three times but did not work. Getting my interest lost kind of situation now. [-(
  10. M

    Evinrude 9.9 HP Model # 10924B

    Thanks. I will redo the pump tomorrow.
  11. M

    Evinrude 9.9 HP Model # 10924B

    Changed the bulb. Still doing the same thing puttering and shut down. If choke open it runs little longer.
  12. M

    Evinrude 9.9 HP Model # 10924B

    I will change the bulb and retry. If it doesnot work than will again reassemble it. Didn't do the blow test once done but fuel is coming from pump exit when I press the bulb. Thanks
  13. M

    Evinrude 9.9 HP Model # 10924B

    Fuel pump was clean and looks new, so does the carb. I don't know who design those clamps that broke my nails. Simple zip tie do the job. Here are the pics for fuel pump. Thanks
  14. M

    Evinrude 9.9 HP Model # 10924B

    Hand pump help. One strange this happening when I unplug hose that goes from fuel pump to the carb; After I pump the primer bulb and stop pumping, all the fuel is going back to the tank. May be culprit is the check valve in the bulb. Will buy the bulb. Can used the same hose or replaced it with...
  15. M

    Evinrude 9.9 HP Model # 10924B

    I cleaned the fuel pump diaphragm and filter. Now it only start with choke and dies down immediately. :-(
  16. M

    Evinrude 9.9 HP Model # 10924B

    Also while my motor is giving me trouble, my Zodiac from the bottom of the Transom start leaking while on the middle of the lake. I managed to make it to boat launch on time. I'm unable to peel the patch from bottom outside and inside. Can I patch both side on top of the existing patch. Can I...
  17. M

    Evinrude 9.9 HP Model # 10924B

    OK I will give a try. Thanks for the suggestion. What you think of this video suggesting the check valve and hose is bad.
  18. M

    Evinrude 9.9 HP Model # 10924B

    Thanks. Yes I cleaned the carb today and before setting it back I tried to pump the primer bulb, clean fuel is coming out from the pipe which goes to carb. Once I start it again it keep shutting down as look like a sound of out of fuel. I restarted and keep pumping the bulb than it keeps...
  19. M

    Evinrude 9.9 HP Model # 10924B

    Thanks. I am able to start but it keep shutting down in lake after 4 minutes.
  20. M

    Evinrude 9.9 HP Model # 10924B

    Hi! I just purchased Evinrude 9.9 HP Model # 10924B. I couldn't find the manual as its says refer to manual to start. There is a two battery terminals coming out of the motor but here is no start button I can find. 1. Starting cord is locked, 2. Gear lever is in forward position and unable to...
Top