Search results

  1. kingsfisherman

    lost trim function after testing coil

    I installed the trim limiter so I didn't have to guess if I was in the "safe zone" when trimming the drive. Usually the promblems I've had stem from wire corrosion and bad connections
  2. kingsfisherman

    leaky throttle shaft on TBI

    I noticed some fuel leaking at the throttle shaft of my TBI and the throttle was sticking at idle, I've read about bushings for this problem. Has anyone done the bushings or had it done on their TBI?
  3. kingsfisherman

    voltage regulator?

    Hello, 65 amp alternator, doesn't kick in when first started but does after increasing RPMs, is that the voltage regulaor going out?
  4. kingsfisherman

    Volvo outdrive water exhaust

    water should not becoming from between the gear cases.
  5. kingsfisherman

    Volvo outdrive water exhaust

    there is an exhause outlet at the transom as well as through the prop hub and cavitation plate
  6. kingsfisherman

    lost trim function after testing coil

    well I got the trim to start working again after splicing the broken black wire but the trim gauge is still pegged, I did try to adjust the sending unit to the 11 ohms prior to finding the broke wire, so I will revisit the sending unit setting tomorrow, thanks for following!
  7. kingsfisherman

    VSR vent line full of fuel

    refresh my memory, way to many things going on to remember all the ideas.
  8. kingsfisherman

    lost trim function after testing coil

    update#4 went ahead and cut the black wire at the sending unit connectors side and spliced it it the limiters black wire. will test it soon.
  9. kingsfisherman

    lost trim function after testing coil

    update #3 found the Black wire broke at the backside of the trim limiter connector to the sending unit, can I cut the connector out and splice these wires? I know the sending unit uses resistance to tell the limiter the position of the drive, will splicing the wires affect that function?
  10. kingsfisherman

    lost trim function after testing coil

    update #2 was able to operate trim in both up and down while using the override switch.
  11. kingsfisherman

    Trim tilt down but not up.

    I also have a Striper Sport Cabin with the same engine, I found a trim limiter on Ebay and installed it to keep my drive in the right range of trim while under way. Got tired of the guess work.
  12. kingsfisherman

    lost trim function after testing coil

    update: I tried using the override switch and the drive comes up but won't go down. I'm sure it was in the right range to go up or down prior to the testing. So for some reason I only have trim up when I use the override switch.
  13. kingsfisherman

    VSR vent line full of fuel

    pressure at test valve atop VSR at 9psi., so I guess I will try again on adjusting the float, right after I figure out why I lost O.D. trim function after testing ignition circuit.
  14. kingsfisherman

    VSR vent line full of fuel

  15. kingsfisherman

    lost trim function after testing coil

    Hello All, I was doing some ignition testing and after doing the test in step 9 (see pic) I lost the trim function and the gauge is pegged, what could have happened? Note: I do have connection between the switch and the limiter.
  16. kingsfisherman

    Low voltage to fuel pump relay

    so it's a GS not a GSi?
  17. kingsfisherman

    What engine in new boat

    I have the same intake on my '98 5.7 GSi engine, 3856270
  18. kingsfisherman

    What engine in new boat

    you might have to find the block casting numbers to figure it out
  19. kingsfisherman

    What engine in new boat

    stupid legaleese
  20. kingsfisherman

    Low voltage to fuel pump relay

    I guess it doesn't have the S.L.O.W. mode option
Top