Search results

  1. R

    CROWN II AUTOMATIC MARINE INVERTER CONNECTIONS

    Hello all, I have a crown II automatic marine converter model R3012F-3, I located a connection diagram on line but looking at the present connections I am not sure if it is the right connection. I have three deep cycle batteries in this older Nautaline houseboat, 73 model I think, currently all...
  2. R

    125HP force tilt trim operation

    Hello all, I have a tilt trim pump I am reinstalling on my outboard, I changed the hydrolic body, I have it hanging to test out prior to pulling the outboard off of the boat, I have the lines connected to the pump according to the manual but when I go up the trim goes out but the tilt comes in...
  3. R

    johnson lower unit change over

    Hello all, awhile back I found a link posted on johnson outboard lower unit direct change overs, I have a 1970 60hp electric shift and a 1968 55hp electric shift and was trying to see if they would swap over. I know where I can get a 1970 40hp and was trying to see if it will change over also...
  4. R

    Will it fit?

    Hello all, I found a 1970 60 hp Johnson and have a 55 hp Johnson and was trying to find the year of my Johnson to see if the lower units will swap over, they look the same. The model # on mine is TLR-10R and J2931296 Both are electric shift, any help out there.
  5. R

    125hp force tilt & trim line connections

    Hello all, I have a 89 force 125 hp that I was told had the wrong tilt and trim pump. the tilt worked but not the trim, I purchased another unit with cylinders and do not know where the hydrolic lines connect up. The old unit had 5 ports and the new one has 4 ports and I only have 4 lines, two...
  6. R

    Ted Williams 7.5hp air cooled outboard

    Hello, I am looking for information on the carb element, is it supposed to have a slit in the end of it? mine does and it is at a 45 degree angle, my motor is trying to flood out and the float seems to be seating good and the fuel in check valves seem seating good, any ideas out there? I cannot...
  7. R

    Force 120 steering froze up

    Hello all, I have a 1994 force 120 that the steering tends to freeze up after setting a while, I pump grease into the steering fitting on the motor swivel but it seems to not be getting to the lower bearing, how can I remedy this? Russell
  8. R

    Dragonfly outboard

    Hello all, Has anyone out there heard of a Dragonfly air powered outboard? I was told it was made in the mid 50's, I picked one up at a flea market not knowing what it was but being the first to ask I had to get it. I have not tried to do anything with it yet but the seller said he could not get...
  9. R

    1972 125hp johnson froze up

    I picked up a 1972 125hp, like new for its age, johnson outboard and was told it has been in storage for about five years and was only used in fresh water. This motor is froze up and I would like to know the best way to free it up? like I said this looks great for its age, I was planning to pull...
  10. R

    1995 120hp force flywheel

    Hello all, I did a bad thing to my force 120, I am switching all me electrical from a 1994 (?) 120 force to a 1995 120 and could not get the flewheel off, I used a puller, impact gun, propane bottle then a propane torch which did it. My problem now is I put to much heat on the center magnet and...
  11. R

    1966 3.9hp Merc

    Hello, I have a 1966 3.9HP one cylinder merc, I am mixing my fuel 50 to 1 but I do not think it has the right spark plug. I was wanting to ask if anyone knows the plug I need and the spark gap setting also could my fuel be to rich for this year?. I have read that older motors should be run rich...
  12. R

    120 hp Force

    Here is a tricky one, I purchased a 1996 120hp with a bad powerhead so I could put the lower unit on my 120hp but it is not made the same, my 120 is not as beafy as the one I purchased so I think mine might be a 1995, I cannot make out the serial #, Just how diffrent are the powerheads from one...
  13. R

    1967 Sears 3.5 hp fuel connector

    Hello all, I am trying to locate a fuel line connector for a Sears and Roebuck 1967 outboard (made by Clinton)air colled motor. This has a large ugly looking connector. The Sears model # is 582 6091 serial # 74622, If there is a way to modify this I will try and do it. I purchased this off of...
Top