Latest activity

What's new New posts Latest activity

P

pae0332 reacted to alldodge's post in the thread lack of power on 4.3 thunderbolt 5 with Like.

Set at 10 BTDC and it is advancing (getting to and hope fully past 20* BTDC) Start with the basics, compression test

Yesterday at 5:46 PM
C

cyclops222 reacted to ski2rule's post in the thread 1963 Montgomery Ward Sea King / Starcraft Starchief with Like.

Yes

Yesterday at 5:37 PM
C

cyclops222 reacted to cadmaster02's post in the thread 1963 Montgomery Ward Sea King / Starcraft Starchief with Like.

That's why I listed the actual manufacturer along with Montgomery Ward. The Joys of doing a Resto-Mod is nothing going back into this...

Yesterday at 5:36 PM
C

cyclops222 reacted to cadmaster02's post in the thread 1963 Montgomery Ward Sea King / Starcraft Starchief with Like.

Next Up, was the transom. This needed help! evidently there was an I/O option on this boat so there was a large oval that was...

Yesterday at 5:34 PM
Fun Times replied to the thread Would high fuel pressure cause misfire.

Because the engine was running rich in fuel and seemingly repaired, you’ll still want to pull, inspect and probably clean or possibly...

Yesterday at 5:30 PM
M

Mc Tool replied to the thread What is this connector and bracket? Fishfinder/GPS/etc.?.

I think that you can prove accuracy on most stuff by checking consistency . Check the same thing a few times and see if you get the same...

Yesterday at 5:29 PM
C

cyclops222 replied to the thread I didn't want to restore this 1997 Islander this summer.

Why are you sweating about doing foam on the bottom ? My small Aluminum boat has all the foam in the space under the full width bench...

Yesterday at 5:26 PM
nola mike reacted to Jmunk's post in the thread I'm doing my Bellows. Mercruiser A1G1. Are the Amazon Bellows Kits any good? with Like.

Mercruiser parts are made to their standards. When they are copied they are made to a price point. When that happens concessions have to...

Yesterday at 5:20 PM
nola mike reacted to Rugglesworth's post in the thread Help me identify whether I have a 1" or 1 and 1/8" shaft with Like.

thanks y'all. I was right it is a 1" shaft. When I went to the marine shop yesterday asked for a 1" shaft and measured it and it was the...

Yesterday at 5:19 PM
Scott06 replied to the thread What are these wires and how does my spedo work?.

The wires are for the trim gauge and or limit switch. Common they get brittle and break. By gen one alp h drive had a separate pito on...

Yesterday at 5:18 PM
nola mike reacted to Hatch19's post in the thread Mercruiser 3.0 overheated, Is my motor shot? with Like.

Checked a couple things this morning. Oil is still full and clean. No external oil leaks I can find. Quick Look at the exhaust...

Yesterday at 5:17 PM
nola mike replied to the thread Mercruiser 3.0 overheated, Is my motor shot?.

No

Yesterday at 5:16 PM
nola mike replied to the thread Mercruiser 3.0 overheated, Is my motor shot?.

His overheat occurred after the transom

Yesterday at 5:16 PM
F
Fj40fiji replied to the thread I didn't want to restore this 1997 Islander this summer.

Progress. I need just a few 5/8” rivets, had to put pop rivets for now.
Yesterday at 5:14 PM
E
evantful posted the thread EVC Control panel fault w/code in Volvo Penta I/O & Inboard Gas Engines & Outdrives.

2009 Volvo Penta 5.7 GXIE-K, DPS-A, EVC-3, Single engine application. Hi all, I developed an EVC Fault that is effecting the helm...
Yesterday at 5:14 PM

Show older items

Top

View All

View All

View All

View All

View All

View All

View All

View All

Boat Bimini Tops

Boat Covers

View All

View All

View All

View All

View All

View All

View All

Latest activity

Follow Us