Latest activity

What's new New posts Latest activity

K

kevinwatkins2003 replied to the thread Mercruiser 350 MAG MPI missing only at 3000 rpms.

Kenny - did have a new rotor. They are telling me they put on the usual AC 41-932 platinum plugs. I'll have to try to look at one and...

Jul 2, 2025
S
strike26 posted the thread transducer in Boat Topics and Questions (not engine topics).

I replaced my gps and transducer from a 2002 furno to a 2024 garmin I placed the transducer in the same position as the furno...
Jul 2, 2025
C

CayugaCobalt reacted to Kola16's post in the thread busted bellows mounting flange with Like.

Anything plastic so if your water tube is plastic and the little plastic or rubber grommet things that holds the trim sending wires. I...

Jul 2, 2025
C

CayugaCobalt reacted to Bondo's post in the thread Is pulling engine mandatory or just convenient or overkill with Like.

Ok, then you have to pull the motor 1st,.....

Jul 2, 2025
A

alpha-newbe posted the thread Mercruiser 3.0 1987 engine not running well after warmed up in Mercury MerCruiser Sterndrives & Engines.

Engine idles fine and will run smoothly at lower rpm in neutral and in gear. After running smoothly on the lake for 15 min or so at...

Jul 2, 2025
Fun Times replied to the thread Mercruiser alpha 1 gen 2 alarm sounding.

Try disconnecting the 2 wiring harnesses at the Ignition control module mounted on the upper starboard side of the engine exhaust seen...

Jul 2, 2025
dwco5051 posted the thread Can You Wear This Shirt in Dockside Chat.

Chances are if you qualify for shirt this you are probably already retired. I figure I was the next to last generation for it.
Jul 2, 2025
7

715Steve posted the thread Intermittent idle issue in Volvo Penta I/O & Inboard Gas Engines & Outdrives.

Hi. 2005 VP 4.3gxi in a FW 18 footer Just got the boat back from marina for tune-up and u-joints. Ran fine the 1st day after small test...

Jul 2, 2025
dwco5051 reacted to Bob_VT's post in the thread S A F E T Y B R I E F I N G with Like.

With the 4th Of July this week it is necessary for a safety briefing. PLEASE Do you absolute best to come out of this Holiday weekend...

Jul 2, 2025
P
Pmt133 replied to the thread '89 Arriva 2050 Restoration.

On my 84, I ended up using a carbide carving disc as it seemed most efficient for grinding. One of these: It worked well but you still...
Jul 2, 2025
P

Pmt133 reacted to todhunter's post in the thread '89 Arriva 2050 Restoration with Like.

Spend the money on a dust deputy, a long shop vac hose (mie is 13ft, I think), and a remote control outlet. The long hose allows your...

Jul 2, 2025
dingbat replied to the thread Why don't sea choice 1 1/16 seals fit?.

Seems like a weird size kit. Typically the inner and outer bearings and seals are a different sizes. Do you have a picture or part...

Jul 2, 2025
P

Pmt133 reacted to Crazy_Pilot's post in the thread '89 Arriva 2050 Restoration with Like.

Another weekend of demo and cleaning. I've started grinding the old transom tabbing away and planning for the new wood core. The...

Jul 2, 2025
P

Pmt133 reacted to Crazy_Pilot's post in the thread '89 Arriva 2050 Restoration with Like.

Drive removal went off without a hitch, except that the steering cable nut galled to the threads of the actuator tube and tore those up...

Jul 2, 2025
P

Pmt133 reacted to Crazy_Pilot's post in the thread '89 Arriva 2050 Restoration with Like.

I built a gantry in my garage using doubled up Unistrut, bolted to a third strut sandwiching the trusses and supported by foundation...

Jul 2, 2025

Show older items

Top