Latest activity

What's new New posts Latest activity

Grub54891 reacted to redneck joe's post in the thread Random with Like.

Today at 6:17 AM
C

cyclops222 replied to the thread Flux Marine Outboard Engines . . ..

Electric battery chemicals are mined and transported to battery purifying companies. Then Trucked to actual battery making companies...

Today at 6:14 AM
C

Chris1956 replied to the thread Modern PT lumber.

Cedar is very rot resistant, and superior to pine in several ways. If PT pine was not a lot cheaper that cedar, it would not be used...

Today at 6:13 AM
alldodge replied to the thread 1997 Mercruiser 4.3 LX not running steady steady at idle or higher RPM's.

Are you grounding the Pur/Wht wire before setting timing? Being a 1997 you should have TB5 ignition, and timing should be at 10* BTDC...

Today at 5:49 AM
dingbat replied to the thread 1988 Johnson 70hp inspection.

Bored a couple of cylinder jugs on a lathe w/4 jaw chuck, but no engine blocks. A block would take forever to set up properly on that...

Today at 5:45 AM
alldodge replied to the thread Volvo Penta V6-240 Fuel High Pressure Dropping to Zero.

Welcome There might be to many zero's here. Fuel pressure should be 50 to 60 psi Limp mode clears on it's own once the sensors tell...

Today at 5:39 AM
alldodge replied to the thread 1981 MerCruiser 120 tick/ squeak.

If tick changes with rpm, it most likely is a lifter starting to collapse

Today at 5:29 AM
L

Lpgc replied to the thread Flux Marine Outboard Engines . . ..

Never buy Russian pants because chernobyl fallout.

Today at 5:21 AM
C

cyclops222 replied to the thread 4.3 gxi run without water....

Impossible !! Volvo and Yamaha claim to be the best motors !

Today at 4:25 AM
C

cyclops222 reacted to Scott Danforth's post in the thread Anchor roller mounted on bow wooden plank with Like.

One snag of the anchor and the rode will snap that bit of teak right off the bow. Anchor chutes and rollers are usually mounted in...

Today at 4:04 AM
L

Lpgc replied to the thread Ford 302 engine oil dipstick - 1995 OMC Cobra, Ford 302, VolvoSX.

Is that fully or semi synthetic? I think I used to see a much wider range of oils than seem to be available now. These days it seems...

Today at 3:26 AM
Scott Danforth replied to the thread Anchor roller mounted on bow wooden plank.

One snag of the anchor and the rode will snap that bit of teak right off the bow. Anchor chutes and rollers are usually mounted in...

Today at 3:26 AM
M

Mc Tool replied to the thread Nobody fishing?.

Yeah heh heh heh , it good watching some deserving git getting his arse handed to him 😆

Today at 1:54 AM
A

acadian2022 replied to the thread 1980's serial number / harness / general questions.

Quick update nothing Ive done worked. I was able to tap a new hole in the ram and got the power trim system to work for now this will do...

Yesterday at 11:56 PM
A

acadian2022 replied to the thread power trim removal of center cylinder.

Quick update nothing Ive done worked. I was able to tap a new hole in the ram and got the power trim system to work for now this will do...

Yesterday at 11:55 PM

Show older items

Top

View All

View All

View All

View All

View All

View All

View All

View All

Boat Bimini Tops

Boat Covers

View All

View All

View All

View All

View All

View All

View All

Latest activity

Follow Us