Latest activity

What's new New posts Latest activity

M

mr 88 replied to the thread Building a fishing boat..

The prop should be matched to the maximum rated RPMs of the motor. Ex , motor rated for 5,000 rpm and all you get is 4,400 which means...

Tuesday at 12:12 PM
redneck joe replied to the thread Starting a 1974 Tri-Hull Restoration, it's a Stryker Mark IV model. Need help with any information or an owners manual..

Well, it appears you have a well thought out redneck frankenstien boat. Enjoy.

Tuesday at 12:09 PM
redneck joe reacted to Pvaughan23's post in the thread Starting a 1974 Tri-Hull Restoration, it's a Stryker Mark IV model. Need help with any information or an owners manual. with Like.

Through bolted, drilled the pilot holes and used a small detail brush to seal the insides before feeding the bolts through and sealing...

Tuesday at 12:08 PM
FLATHEAD reacted to aspeck's post in the thread Trail camera issues fixed, now pics from them ... with Like.

I have a really nice scrape line forming ... but haven't seen the maker during daylight hours. Need to set a camera up to see what size...

Tuesday at 11:57 AM
FLATHEAD reacted to flashback's post in the thread Trail camera issues fixed, now pics from them ... with Like.

This little one was curious.

Tuesday at 11:56 AM
E
eddie the boat guy posted the thread Does anyone know what this plug is called ?? in Mercury & Mariner Outboards.

That black plug that covers the shift linkage arm access
Tuesday at 11:56 AM
C

cyclops222 posted the thread Computer with 11 update wants me to log in 2 times as a password action. DUUUHH in Dockside Chat.

The drug addicts & drunks now control computer security. Stupid stupid

Tuesday at 11:48 AM
T

tphoyt replied to the thread Trail camera issues fixed, now pics from them ....

My buddys dad got 220# buck the other day which is big for here. He managed to drag it back to the truck but then realized he couldn’t...

Tuesday at 11:14 AM
S

ShoalSurvivor replied to the thread Alpha 1 Gen 2 - leak & transom service questions.

Ok, plan for today: 1) hose in Ypipe to see if leak appears 2) if yes, then check for loose screws and see if tightening them resolves...

Tuesday at 11:04 AM
nola mike reacted to Rivergator's post in the thread The easiest and most precise way to install a gimbal bearing with Like.

A few days ago I got around to replacing the gimbal bearing in my Alpha One Gen1 drive. I have the alignment shaft and installment tools...

Tuesday at 11:04 AM
S

ShoalSurvivor reacted to Bt Doctur's post in the thread Alpha 1 Gen 2 - leak & transom service questions with Like.

rot in transom, corrosion of the Y pipe or corrosion of the transom housing May have to pull the motor to determine what part it is

Tuesday at 10:44 AM
S

ShoalSurvivor reacted to Scott06's post in the thread Alpha 1 Gen 2 - leak & transom service questions with Like.

if the Y pipe was leaking and you stick a hose in bellhousing the water should go through the engine and leak out the Y pipe, engine...

Tuesday at 10:44 AM
J

jetboater replied to the thread I want to add a third toon of smaller diameter.

Chris1956’s idea about the wooden blocks in a good one. A crazy idea—have you considered adding BOTH of the 19” tubes side by side...

Tuesday at 10:30 AM
R

racerone replied to the thread Evinrude or Suzuki.

Does the motor have the correct prop on it for operation on a pontoon boat ?----Diameter and pitch of your prop?

Tuesday at 10:00 AM
C

Chris1956 replied to the thread Evinrude or Suzuki.

You did change the oil filter, when you changed the engine oil, right? Pump grease into the grease fittings and clean and grease the...

Tuesday at 9:50 AM

Show older items

Top

View All

View All

View All

View All

View All

View All

View All

View All

Boat Bimini Tops

Boat Covers

View All

View All

View All

View All

View All

View All

View All

Latest activity

Follow Us