What's up, guys. I'm thinking about grabbing another boat. It's a 2004 Bayliner 249 sundeck. I'm not crazy about Bayliner and the way their stuff is put together. But I've never looked at one this recent. Anybody have any thoughts on them? Are they built better than the older ones. It seems...
1994 Merc 5.7. There is a clacking noise that comes from the front of the engine at high rpms. Mainly when you gun it out of the hole and if you're running above 3800 rpm. Cruising at 3200 or so there is no noise. Seems to not happen as much after you've run for awhile. This is not constant...
1994 Monterey 206. 5.7 with 2bbl mercarb TB IV. I have this thing running really well, save one problem. Have replaced plugs, rebuilt carb, soaked carb and blown everything out. Set everything to spec. Set timing and idle. Dead on. Starts up with ease and idles at 750 like a clock. Will...
1994 mercruiser 5.7. I need a replacement tube, but I can't find one anywhere. Does anyone have a link or know where I can look. Maybe I'm just a moron, but I can't dig it up. Thanks fellas.
Alright, fellas. Here's one more from this never ending project. Finally have everything dialed in to where she starts up and idles steady. Just noticed there is a faint white smoke at the front of the engine. Looks like it's coming from behind one of the pulleys, but with the engine running...
Trying to dial in my 1994 5.7. Starts easy, idles smooth. Just set the timing. Rev response is very good. However, when I rev it up and let it come back down, it dies. Starts right back up no problem. I have rebuilt the carb. Took it apart and let it soak like I should. But maybe I missed...
Rebuilt mecarb for my 1994 5.7. Putting it back on and had a question about gaskets. I didn't pay attention to the base gasket when I pulled it, and my kit came with two. One has 2 circle openings and one is just a big oval. Bolt patterns are the same. The oval is a good bit thicker as well...
This seems like a dumb question. I have a 1994 Monterey 206. I changed out the gimble bearing. It was the first time I've ever done this. I thought it was seated. It's straight. There is about a 1/4 " behind it between the bearing and the seal. I want to know is this right or does it need to go...
1986 Rinker V170 2.5 120 Had boat out today and for the third straight time, runs really good for 2-3 hours, off and on pulling skiers and tube . Thenlike clockwork, it starts to cut out, like it's starving for gas . It will start back up and I can idle it back. Sometimes it quits when I'm...
86 rinker with a 120 mercruiser engine .Boat runs well . Doesn't stall. After long runs of yanking a skier or tube and shutting down, it takes a little longer to start. Always does, but jjst takes longer. When I first put in the lake, it starts with a touch of the ignition. Just curious what I...
1986 rinker v170 with a 120 engine. Was on the lake yesterday, running good. Started every now and then to lose a little power .Like it's starving for gas. Would go back to normal. Then all of a sudden just quit .Wouldn't start up again . Checked the carb and no gas in bowl. Removed the line...
I bought a 1986 renken bowrider with a Merc 120 in it about 1 1/2 years ago. Just finished fixing up the interior and started on the engine . Started it right up and it idled fine, but when I accelerate to 2000 rpm it would cut out and die . Replaced the fuel/water filter and drained the tank of...
I'm re-doing my side panels on my boat . The panels were so far gone , I didn't have to take the throttle apart to remove it .I just pulled the rotten wood away from it .I'm about to reinstall the new panels and need to reattatch the throttle .for the life of me, I can't get the handle to...
