Recent content by Chuck4741444

  1. C

    Seastar hydrolic steering testing

    I tested the pump with the lines disconnected using a 1/4 valve and gauge on each hose, i could see it moving pressure from one line to the other... It's a bad plunger... thank for responding.
  2. C

    Seastar hydrolic steering testing

    I found the problem, the polymer seal on the plunger is letting fluid through. I stopped testing pressure at 300. That's all my gauge read, I could get more press. I have found a company that sells the rod with the plunger and seal together. For about 125.00 I couldn't find the o-ring and the...
  3. C

    Seastar hydrolic steering testing

    I'm having problems after I hit the motor putting extreme pressure on. I lost my steering. Things done i have bleedit to death many times. I have removed it an totally disassembled it twice, every thing was oily and spotless clean, removed the 4 springs and ball bearing twice. Secondtime I...
  4. C

    Teleflex sterring

    I'm needing a new sterring cable for sh5023 helmet sterring box. My old cable is ss07217. I can't find a replacement for it. Are these cables replaceable? Or do i need to replace everything?
  5. C

    Over revving

    1987 j 48 rebuild cards, fresh gas. It's starting on manual hockey, ideal rough. Sometimes it starts revving like thet when they are running out of fuel. The settles down to rough idea. After 20 minutes of messing With it. It has started revving out of control on its on, I had6to chock it...
  6. C

    Seastar hydraulic

    I have damaged part number 5 on my pump HH5271 build-in lock valve for positive rubber lock. Seastar doesn't sell this part. Does anyone know where I can buy one? Thanks.
  7. C

    Steering setup

    I'm looking to replace the steering system on a 87 johnson 48 hp. Most I look at are Chinese and universal. Will they work on my boat? Where is a good place to one of good quality?
  8. C

    97 mercury 115 hp. Drive shaft removl

    I can't get the drive shaft out the lower unit. Pinion gear nut is off, the crankshaft seal housing is off. In the pictures there something that looks like the back of a seal ive tried to drill a small hole, so I can pull it with a puller. I don't have a manual. This is a one time seal job for...
  9. C

    Steering issues on a SeaStar steering

    I know this is and old post, I put excessive pressure on the sea star hydraulic cylinder. I belive I blew the internal seal, I can turn the wheel non stop either direction, and can push the motor side to side. There is no resistance. I have no leaks. She is full of fluids It almost like the...
  10. C

    Johnson PTT colors

    I'm connecting a 96 150 Ignition wire harness a 1990 150. The 90 has 4 wires for TT BLUE, GREEN, RED, AND BROWN. the 96 has BLUE ,GREEN AND A WHITE I only have a manual for the 96. I would think the red would connect with the white with tan stripe for power. What is the brown on the PTT plug...
  11. C

    Lawrence FS 9

    What's the best, avionics or c map?
  12. C

    Lawrence FS 9

    I had a Lawrence elite ti2 I was had problems, it was about 3 years old, I sent it in under a 50% warranty, 220. To fix or 460. To replace it. With a 6 month warranty. They sent me a Lawrence elite fs 9, The problem is the typographical maps Is not very detailed, it's missing a 2 mile...
  13. C

    Acceleration problems

    I have the link and sink set. I was thinking that when it started moving, and fell in to the recess slot, would could be a problem. I'm taking out tomorrow to see how it does
  14. C

    Acceleration problems

  15. C

    Acceleration problems

    My cam is not sitting in the notch. I used a parts motor that was supposed to be a 95, it had the red plug in. I could have used the wrong one.
See more
Top