Recent content by NESAR

  1. N

    Looking to change my distributor

    Hello I have a 1974 chrysler inboard 318 engine with points in the distributor . I'm looking into replacing it with electric. How hard is it to replace and what would I need for parts? Reason I would like to change it is the fact that I can't find anyone to work on it and when it gets hot the...
  2. N

    200hp Johnson outboard controls & wiring harness question??

    it's a 1990 200hp Johnson outboard I need the controls & wiring harness from the controls to the motor any link or info that would be great. I don't know what ones to get for the engine.
  3. N

    Marine Alternator question.

    Sorry if this is not posted in the correct spot. Here is my question... I have a Chrysler 318 engine the alternator is shot. I would like to get a new one but not sure if the one I'm looking up will fit. I have two links the first link is the alternator I have in the boat now...
  4. N

    Mercury outboard 175hp Blackmax 1985 (overheating)

    Hello, I have a few questions? I just had my motor worked on and is overheating this is what was done. Thermostats (one on each cylinder head), poppet valve and impeller has all been done. The boat has no gauges hooked up at this time because we have not finished it yet. When we took it in a...
  5. N

    Poppet valve 1985 175 black max!

    Anyone know where I can order one online? Any info you can help with would be great. Link would also be nice if you can. This is the list of parts but I cant find it in any of these. ACCESSORIES BLEED SYSTEM BOTTOM COWL CRANKSHAFT, PISTONS AND CONNECTING RODS CYLINDER BLOCK AND END CAPS...
  6. N

    New Impeller now it's not shifting into gear?

    1985 merc blackmax 175hp I had someone replace the impeller and it no longer shifts into gear. What could have gone bad? When I looked it over there was a pin that wasn't replaced in the shaft I replaced it but still wont go into gear.
  7. N

    175 merc black max outboard engine question??

    I have noticed that on the side of the switchbox assembly there is water coming out of a hole, It's a good stream too. I was wondering what the name of the part is, or if anyone has a diagram of the starboard side of the engine so I can look it up. it's a 1985 - 175 merc black max outboard.
  8. N

    20' Starcraft wondering if anyone knows the year of this boat?

    I am looking for information on this boat. I am having problems with the prop and cant get any info from the dealers. I'm looking for year max power/HP for the boat any other info would be great. I have a 175 HP merc on it and it seems that it has to much motor. I think it is early 70's Islander...
  9. N

    Can some tell me how a prop spins?

    I have lots of post up on this boat we built. My first post was this: When I put it WOT the prop spins out of the water and if I trim it down to keep the prop in the water it drives the bow under the water. So I took my cousin out he said the prop is spun. Put on a new prop the old one was 19...
  10. N

    New Prop how to install it correctly, old prop spun.

    Hi everyone, Okay Here is my old problem. I took my 20' boat out and couldn't trim it I was thinking the prop was coming out of the water,well it wasn't the prop coming out of the water it was freely spinning at 1/4 throttle. The old prop was 19 pitch the new one is 23 pitch 3 blade aluminum. We...
  11. N

    175 merc outboard prop question.

    Re: 175 merc outboard prop question. Here is a picture of it lowered. hope this helps. it was taken at night so its not the best picture. It looks to be correct but like I said it is off 1'' by the measurements.
  12. N

    175 merc outboard prop question.

    Re: 175 merc outboard prop question. Okay measuring the transom it is 20'' and measuring from the A/V plate it is 21'' so I am 1'' to long will that make a big difference in how the boat prop is running? I can not lower the motor anymore then where it is sitting ,I'm on the top hole. I can...
  13. N

    175 merc outboard prop question.

    Re: 175 merc outboard prop question. I dont know the year of the boat but,I did snap a picture to show you what i'm working with. hope the pic works this time;-) sorry i don't no what a antiventilation plate is.
  14. N

    175 merc outboard prop question.

    I'm new to boating so please excuse me. I have a 20' starcraft and a 175 merc black max. I put the boat in the water today for the first time after rebuilding the boat. Here is the question when I put it WOT the prop spins out of the water and if I trim it down to keep the prop in the water it...
  15. N

    Tachometer question 1986 Merc Outboard ???

    Just have a quick question? Is there a certain tac I need to get for my motor? I would also like to know who to hook it up on the motor side? If you know of any youtube vid that I can take a quick loo at,I can't seem to find any. PS. it is a 175hp
See more
Top