I just moved and my manual is packed away no where to be found. I'm replacing the head gaskets, cover gaskets, poppet valve & thermostats and can't find the torque specs anywhere online.
Can someone please help me out, need to get this boat running and sold ASAP cause in financial crisis..
Please?
I believe it's around a 96-99 yamaha 115 but the trim bracket decal is gone an the circle sticker on block is gone, already confirmed with yamaha they don't cast numbers in the block.
So....
I have some pics of the motor an just pulled the carbs off an found cast numbers on the carbs. Hopefully...
I have a 1992 Mariner 115 inline 4 installed, I just picked up a 1998 Yamaha 115 with control box.
Can I use the brand new installed teleflex cables with some sort of adapters for the yamaha control box an engine side?
Do I need to change any of the wiring for the gauges? Yes I have the yamaha...
I have a 1986-7 mercury 150hp powerhead an a 2001 with a thrown rod through the block so was wondering if its an easy swap onto the mid or will there be exhaust flow issues? Thank u in advance.
I have a 1999 Fun Sport 215 deck boat that weighs 2100lbs (according to Nada.com) I bought it without an engine. My question is will a 1989 Mercury 135hp v6 with 120lbs compression be under powered for this boat? I live in Florida an will be spending most of my time out in the gulf of mexico but...
Ok I been researching the past for days on this. I'm having such a hard time finding a 20" shaft v6 motor for under $2500. that's decent so been reading that if I use a manual or hydraulic jack plate I can use a 25" shaft motor but some say you loose hole shot performance, top end speed an...
I have a 19' Keywest 1900 CC with a 1985 Johnson 120 Looper.
I have the XP150 on my motor stand getting some work done.
My question is, from personal experience only which is a better built/reliable motor?
I'm not talking about condition of my present motors I'm talking about comparing the 2...
The other 5 cylinders have between 80-90 psi.
The motor has been sitting for a while.
I'm wondering since compression in 1 cylinder is that low is it a broken reed? Dropped cylinder?
Seems to be too low for a stuck ring?
I will be taking off the head tomorrow to check the cylinder but wanted...
1985 Johnson 120
Compression: 123/123/130/130
OK I had the plastic carb warpage an then I took the carbs of my donor 1992 120.
They are a different part number but compared the internals of the bowls internals an only part no that is different was the needle/float valve assembly (the needle...
I have a 85 Johnson 120 looper that has plastic carbs, the carbs are warped especially at the float bowls.
I picked up a 92 Johnson 120 looper an the plastic carbs seem to be straight. The only difference I see between the 2 is the shape of the side metal plates an on the bottom of the carb...
My model is 130tlrq, year 1992, been searching the net for hrs an can't find the p/n for the manual I need...
Anyone please help I'm new to Yamaha. Thanks
1985 Johnson 120 J120TLCOS, not only are the float bowls warped but on top of each carb where they mount to the throttle body I see gaps...I heard BRP sells replacement aluminum bowls but what do I do about the plastic carb body being warped? But all new plastic carbs so it will do it again??
I...
Just bought a used 1978 Johnson 175hp an it has a Teleflex seastar HC5342 front mount arm, did not come with any other controls or hoses. My question is, does this system replace the original steering tube or does this fit through it?
Also I have a 1985 Johnson 120 on my 19' Keywest center...
OK I have a 19' Keywest 1900 open fisherman an the steering is stiff, took the outboard off an steering still has tension, so I picked up a parts boat that I'm using the engine off if an the steering is very easy an noticed it has a tack an pinion steering set up. The cable itself will probably...
