Search results

  1. D

    Pressure test 1990 Alph1 Gen1

    Hello All, I recently replaced seals on my outdrive. Did both upper and lower. Shift shaft seal, replaced impeller with all new seals and replaced bearing carrier. I replaced everything but the universal joint seal on the top half since it is a bit tricky to get the preload correct. Did a...
  2. D

    Fuel tank dimensions 1990 Bayliner 2651

    Looking to replace my fuel tank on a 1990 Bayliner 2651. Gotta cut the fuel tank from the aft cabin. I can determine the width by visual inspection in the engine compartment, I just don’t know the length. Anyone have a ballpark length of the tank? Any help would be appreciated.
  3. D

    Interior fabric

    Hey all…. Looking for advise on the best fabric to use for the interior cabin cushions. Has anyone tried outdoor fabric? I’m in the process of redoing bar stools and when I was searching for fabric on line I came across “ outdoor fabric” Curious if anyone has tried using this type of material...
  4. D

    1990 Bayliner 2651 Fuel tank dimensions

    Good day all! Looking to remove/ inspect/ and-or replace my fuel tank. I can determine the width of the tank since it’s viewable from the engine compartment I’m just not sure of the length. I’ll need to cut out from the aft cabin. Anyone know the length of the tank? Anything else to consider for...
  5. D

    70hp Force shift adjustment

    Having a bit of an issue with shifting into neutral. When I throttle down from forward to neutral I must go just a little past neutral to get prop to actually get her out of gear. Seems like a small fix. Question is- Should the adjustment be made on the stainless steel rod adjustment nuts on the...
  6. D

    Replacing snaps

    Looking for advise on replacing/ cleaning boat top snaps. They are 30 years old and are looking tired. Some snaps are screwed in, some riveted, some are flat out gone. Whats the right steps in replacing or cleaning up those that are there. Curious as to what folks out there have done.
  7. D

    Bottom paint removal

    What is the best way to remove bottom paint? I’ve seen everything from oven cleaner to scraping to sanding being discussed. Any thoughts/suggestions? I’m reviving a 1990 2651 Bayliner. Looks like there’s several coats of various paints. I don’t think the PO(s) took the time to do it right and...
  8. D

    Old insta trim tab hoses

    Looking to replace the old hardened trim tab hoses on a 1990 bayliner 2651.... old insta trim motor works well.....the hoses are rock hard and need to be replaced.....the hose Is readily available on line....... what’s the process for getting the new trim hose off the trim tab cylinder and...
  9. D

    Solenoid for 1990 mercruiser oildyne trim pump

    Can automotive solenoids be used on a the trim pump or must they be a mercruiser/ Sierra/ or marine application only?
  10. D

    Alpha 1 gen 1 bearing carrier

    Trying to pull the bearing carrier out. Heat and homemade puller has broken some of the rear end of carrier. Considering breaking away the rest of the rear end of carrier and taping prop shaft from side to side. Saw some other suggestions using the prop with metal plates to pull carrier and prop...
  11. D

    1993 70 hp force water intake tube

    First, love this site! Very knowledgeable people giving wonderful information. Question regarding the seals/small rubber gaskets that are between the water intake tube and the base plate. I Needed to replace the base plate gasket and the power head to base plate gaskets. Upon ripping these apart...
  12. D

    Replace fuel tank or not

    All, I’ve recently acquired a 1990 bayliner 2651. Trailer kept. Needs TLC among other things. ... Problem is these boats have a tendency to have a leaky fuel tank especially at this age. No signs (or smells) of leaking at this point. It had 40 gallons of fuel in her when purchased. That fuel...
  13. D

    1993 Force 70hp

    To begin, this site is amazing! Thank you to all that have helped sharing information. I’m a newbie to the site. The knowledge shared is impeccable, Got a quick question regarding replacing an exhaust gasket. 1993 Force 70 hp outboard. Is there a sealer or gasket prep that is needed when...
View older results
Top