Search results

  1. SkiDad

    Will this prop work with my Force 125 ?

    Mercury Vengeance Stainless Steel 13 3 8 x 14 Pitch Used Once | eBay http://www.ebay.com/itm/MERCURY-Vengeance-Stainless-Propoller-PART-48-17314A46-14-Pitch-RH-w-hub-kit-/121113897817?pt=Boat_Parts_Accessories_Gear&hash=item1c32f36b59&vxp=mtr 48-17314A46 if so, what do I need to do special to...
  2. SkiDad

    Anyone removed cup from prop ?

    I have a 15 pitch stainless prop for my outboard... picked it up used for cheap. runs faster out of the hole than my 15 pitch aluminum but it is a little slower top end. I'm not too concerned about top end but the thing I have noticed it that it is harder to steer with it on. Stainless...
  3. SkiDad

    Force 125 stainless prop

    I picked up a 15 pitch Michigan stainless prop the other day for pretty cheap. Been looking for a long time - hard to find that pitch. Didn't give them too much b/c i couldn't test it for spun hub, etc. I haven't tested it yet b/c the thrust washer doesn't hit flush with the back of the...
  4. SkiDad

    going to help my dad tomorrow - force 125

    my dad has a '88 force 125. He's never had a lick of trouble with it in the 20 years he has had it. last time we were out at the end of the year it was running weird and it wouldn't idle at a normal speed ... more like 2000 rpm or around there. I'm guessing something came loose on the...
  5. SkiDad

    Anyone put a trim switch on the engine or near ?

    i have an 1985 force 125 - my boat sits very high on the trailer so I can't reach the trim switch on the dash - thinking of wiring one by the engine.... seen an evinrude with the swich right on the engine body. anyone done it and if so what wires ?
  6. SkiDad

    Swivl-Eze Pylon - looking for mounting instructions

    hi Guys, got a used one of these. I contacted Attwood and they don't see to have the instructions for them. Part 96008. Looks like this. anyone have the instructions they could scan and post ? I'm mostly concerned about the recommend angle backwards of the rear pole. Going to back...
  7. SkiDad

    changed the primer bulb - line is 1/4"

    i fired up the boat ('86 Force 125) the other day and the primer bulb was all cracked...so I picked up one at the local marine place for 22.00 - I was thinking 5-10 bucks. Wow I thought that was high, and the lady explained about EPA regulation on new ones. Hate how the EPA does stupid stuff...
  8. SkiDad

    Can I put U-Bolts here for Skiing and Tubing ?

    Hi Guys, this is the back of my 1985 bayliner.... can I put a 2nd set of u-bolts in the blue section ? I'm guessing the transom stops at the white but I wasn't sure. I think I would be OK to hook up in the blue for skiing - but not sure about tubing. I have one of those booster balls...
  9. SkiDad

    Do i need this spacer ?

    i have an 1985 Force 125 - spun the prop hub this weekend and it seemed to also spin this spacer (rounded all the plastic teeth. will it be bad to use as is ? Do I need it ? here is a picture of mine replacement part# f532299
  10. SkiDad

    Trim Bleeding down

    Hi Guys, I did look at some of the other threads about the trim pump but most were referring to how to fix. So... about 1 month ago I noticed that it was bleeding down just on tilt - but trim was holding fine (so i thought no big deal ) Now last time I was out I noticed that the motor is...
  11. SkiDad

    Ski Pylon / tow bar for Bayliner Capri 1900

    Hi guys, i have a 1985 Capri 1900 with outboard. Do you know of a good Ski bar that will fix and attach well.
  12. SkiDad

    2-Cyle spill on Carpet

    I was filling up yesterday and my 2-cycle quart slipped out of the had and it spilled about an ounce on the carpet. I blotted with a towel and used my steamer to try to get it up - but the mark is still there any suggestions on what will get it up safely. thanks
  13. SkiDad

    Maintenance Free Battery ?

    I apologize if this was covered but I couldn't find anything in the stickys or search. I talked with CDI about a new Stator today - i have an '85 Force 125 and I'm pretty sure the stator is fried based on open loop ohm readings. Anything the tech guy at CDI said that they don't recommend an...
  14. SkiDad

    Do I need to do timing after stator replacement

    I'm thinking i doing the stator myself - i'm a little overwhelmed. I got the nut loose on flywhell and can get a wheel puller. But I'm wondering will i loose the timing or will it stay the same when I put the flywheel back on ? suggestions ? thanks !
  15. SkiDad

    No Spark Force 125

    Hi Guys, editing this post. Boat ran good yesterday, ran it WOT for a while to get the engine cleaned up a little... stopped to swim. 1 hour later motor will not start. Not even a pop - just cranking. I thought maybe I just flooded it. pulled the plugs and cleaned, checked filter, choke...
  16. SkiDad

    85 Force 125 - how am i looking / suggestions

    I recently got an 1985 Bayliner 1900 with a 1985 Force 125hp. It has the original 17p prop from day one - no dings or anything - the guy was meticulous about caring for this boat. anyhow, I'm running WOT about 4400 RPM with 2 guys on board and about 12 gallons of gas. GPS is showing 38...
  17. SkiDad

    84 Larson BR

    Hi All, Looking at a 1984 Larson Delta Conic 19' open bow. I can't seem to find this boat on Nada. Can you anyone tell me the value ? It has a 120 I/O. Interior and Exterior in excellent condition b/c the owner didn't use it a ton and was always stored inside. Has been used in the last...
  18. SkiDad

    1988 Bayliner Cobra

    Hi Guys, was is the value of a 1988 Bayliner 18' Cobra. The hull is in good condition- some fading - but better than average, the force 125 runs close to new. The seats are getting pretty cracked but still function. Floor has some soft spots. Has original trailer (some rust). Just...
View older results
Top